Image IMBE39401 user manual This step will require two people

Page 7

3.Tap a 60mm Square Inner Cap (28) into the top of each of the Front Uprights (7).

Attach one of the Front Uprights (7) and two Rack Joint Plates (6) to the Left Base (3) using four M10 x 78mm Bolts (31) and four M10 Nylon Locknuts (29). Make sure the Front Upright is oriented so that the holes on the bottom of the Front Upright and the holes in the Joint Plates line up. If they do not line up, turn the Front Upright upside-down. Do not tighten the Nylon Locknuts yet. Make sure the Front Upright is turned so the adjustment holes are facing the Rear Upright (8).

Attach the other Front Upright (7, not shown) and two Rack Joint Plates (6, not shown) to the Right Base (1) in the same manner.

4.This step will require two people.

Refer to drawing 4a. Have one person hold out the Adjustment Knobs (22) on a Safety Spotter (20), while the other person slides the Safety Spotter down over the right Uprights (7, 8), as shown. Hold the Adjustment Knob out on the Weight Rest (19), and slide the Weight Rest onto the Front Upright

(7). To avoid breaking the Square Bushings (21) inside the top and bottom of the Safety Spotter and Weight Rest, be careful not to catch the Square Bushings on the edges of the Uprights as they slide on.

Refer to drawing 4b. Secure the Safety Spotter (20) and the Weight Rest (19) to the right Uprights (7, 8) by snapping the three Adjustment Knobs (22) into adjustment holes in the Uprights and turning them clockwise until tight.

Assemble the other Safety Spotter (20) and Weight Rest (19) to the left Uprights (7, 8) in the same manner. Make sure both Safety Spotters and both Weight Rests are at the same height.

5.Attach the Chin-up Bar (13) and two Rack Joint Plates (6) to the Front Uprights (7) using four M10 x 78mm Bolts (31) and four M10 Nylon Locknuts (29).

Do not tighten the Nylon Locknuts yet.

3

28

8

7

Adjustment

Holes

 

1

 

 

 

31

 

 

 

 

29

 

 

6

 

3

 

 

 

 

 

6

29

4a

21

4b

 

 

 

 

19

 

 

7

 

 

8

 

21

19

22

 

 

 

 

 

20

 

 

 

 

22

20

 

 

21

 

 

 

22

 

 

 

 

8

 

 

 

7

 

 

5

6

 

 

29

 

13

 

 

 

 

 

 

31

6

 

 

 

 

 

31

 

 

7

 

 

 

 

7

29

7

Image 7
Contents Customer HOT Line Model No. IMBE39401 Serial NoTable of Contents Important Precautions Right Side Before You BeginLeft Side M6 Washer M10 Nylon Locknut M8 Nylon Locknut Part Identification Chart-Model No. IMBE39401Do not tighten the Nylon Locknuts yet AssemblyMake Things Easier for Yourself Nylon Locknuts yetThis step will require two people Tighten all Nylon Locknuts used in steps Page Page Closer to the floor. Do not over tighten the Nylon Make sure that the Backrest Tubes are turned asShown. The indicated holes are closer to one Side. Turn the Backrest Tubes so the holes areLocknut the Seat Mounting Bracket must pivot easily Weight Tube Adjusting the Backrest Adjusting the Weight RackUsing the Curl PAD Adjusting the SeatUsing the Weight Rests and Safety Spotters Adjusting the PAD TubesSetting UP for Squat Exercises Using Olympic Weights on the LEG Lever Attaching Weights to the Weight CarriageTightening the Cables Exercise Guidelines Cooling Down Muscle ChartStaying Motivated Thursday Aerobic Exercise Date Exercise Weight Sets RepsDate Aerobic ExerciseQty Description Part List-Model No. IMBE39401Exploded Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT