Image IMBE39401 user manual Tighten all Nylon Locknuts used in steps

Page 8

6.Press a 60mm Square Inner Cap (28) into the Left Frame (12). Attach the Left Frame to the left Uprights (7, 8) using four M10 x 78mm Bolts (31) and four M10 Nylon Locknuts (29). Do not tighten the Nylon Locknuts yet.

Assemble the Right Frame (10) on the right Uprights (7, 8) in the same manner.

Attach the Center Frame (11) to the Left Frame (12) and the Right Frame (10) using four M10 x 78mm Bolts (31) and four M10 Nylon Locknuts (29).

Tighten all Nylon Locknuts used in steps 1–6.

7.Press the two 51mm Round Inner Caps (42) into the weight tubes on the Weight Carriage (15).

Make sure the Weight Carriage is turned so the weight tubes are near the top, as shown. Attach the lower Carriage Bushing (16) to the Weight Carriage (15) using a M10 x 66mm Bolt (35), two M10 Washers (37), the 51mm Spacer (39), and a M10 Nylon Locknut (29).

8.Insert the two Weight Guides (9) into the Weight Guide Base (4). Attach the Weight Guides using two M8 x 72mm Bolts (33), four M8 Washers (36), and two M8 Nylon Locknuts (30).

Slide the two Weight Bumpers (18) and the Weight Carriage (15) over the Weight Guides (9). Be sure the Weight Bumpers are on the bottom.

9.Press a 60mm Square Inner Cap (28) into the end of the Weight Guide Frame (14).

Hold the Weight Guide Frame (14) on top of the Center Frame (11) and the Weight Guides (9). Attach the Weight Guides to the Weight Guide Frame using two M8 x 72mm Bolts (33), four M8 Washers (36), and two M8 Nylon Locknuts (30).

Attach the Weight Guide Frame (14) to the Center Frame (11) using two M10 x 78mm Bolts (31), two M10 Washers (37), and two M10 Nylon Locknuts (29).

8

6

 

 

11

 

 

 

 

 

 

10

29

 

 

 

 

 

 

 

 

 

 

29

 

 

 

 

28

 

31

8

31

 

 

 

12

 

 

 

 

29

 

 

31

 

 

7

 

 

 

 

 

 

 

 

 

31

8

 

 

 

 

 

 

7

29

 

 

 

 

 

7

42

 

 

 

 

 

 

15

 

Weight Tube

 

29

 

 

 

 

37

 

 

42

 

 

 

 

 

16

39

37

35

 

 

8

 

 

 

9

 

 

 

 

 

 

 

 

15

 

 

30

 

18

 

 

 

 

 

 

 

 

4

 

 

 

 

36

 

 

 

 

33

9

30

36

 

28

 

 

 

 

 

 

 

 

31

 

 

36

 

 

 

 

 

14

 

 

33

 

 

 

 

 

 

11

 

 

 

 

 

 

9

 

37

 

 

 

 

29

 

 

 

Image 8
Contents Model No. IMBE39401 Serial No Customer HOT LineTable of Contents Important Precautions Left Side Before You BeginRight Side Part Identification Chart-Model No. IMBE39401 M6 Washer M10 Nylon Locknut M8 Nylon LocknutAssembly Make Things Easier for YourselfNylon Locknuts yet Do not tighten the Nylon Locknuts yetThis step will require two people Tighten all Nylon Locknuts used in steps Page Page Make sure that the Backrest Tubes are turned as Shown. The indicated holes are closer to oneSide. Turn the Backrest Tubes so the holes are Closer to the floor. Do not over tighten the NylonLocknut the Seat Mounting Bracket must pivot easily Weight Tube Adjusting the Weight Rack Using the Curl PADAdjusting the Seat Adjusting the BackrestSetting UP for Squat Exercises Adjusting the PAD TubesUsing the Weight Rests and Safety Spotters Tightening the Cables Attaching Weights to the Weight CarriageUsing Olympic Weights on the LEG Lever Exercise Guidelines Staying Motivated Muscle ChartCooling Down Exercise Weight Sets Reps DateAerobic Exercise Thursday Aerobic Exercise DatePart List-Model No. IMBE39401 Qty DescriptionExploded Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT Ordering Replacement PartsLimited Warranty