Image 8.0 user manual

Page 18

46.Remove the 3/8” Nylon Locknut (50) from the indi- cated 3/8” x 5 1/2” Bolt (55).

Wrap the Leg Press Cable (75) around a 3 1/2” Pulley (24). Secure the Pulley and a Cable Trap (25) to the 3/8” x 5 1/2” Bolt (55) on the indicated side of the Press Base (6) with the 3/8” Nylon Locknut (50). Be sure the Cable Trap is oriented to hold the Cable in place.

Press a 2 1/2” Square Inner Cap (76) into the Press Base (6).

47.Remove the 3/8” Nylon Jamnut (63) from the indi- cated 3/8” x 4 3/4” Bolt (60).

Wrap the Leg Press Cable (75) around a 3 1/2” Pulley (24) in the direction shown. Secure the Pulley and a Cable Trap (25) to the 3/8” x 4 3/4” Bolt (60) on the indicated side of the Press Leg Lever (90) with the 3/8” Nylon Jamnut (63). Be sure the Cable Trap is oriented to hold the Cable in place.

48.Remove the indicated 3/8” Nylon Locknuts (50).

Wrap the Leg Press Cable (75) around a 3 1/2” Pulley (24). Attach the Pulley and a Cable Trap (25) to the 3/8” x 4 3/4” Bolt (60) on the indicated side of the Press Seat Frame (7) with the first 3/8” Nylon Locknut (50).

Wrap the Leg Press Cable (75) around another

3 1/2” Pulley (24). Attach the Pulley and a Cable Trap (25) to the 3/8” x 4 3/4” Bolt (60) on the indi- cated side of the Press Frame (8) with the other 3/8” Nylon Locknut (50).

Be sure the Cable Traps (25) are oriented to hold the Leg Press Cable (75) in place.

49.Remove the indicated 3/8” Nylon Locknut (50).

Attach the Leg Press Cable (75) to the 3/8” x 3 1/4” Bolt (62) on the indicated side of the Press Upright

(2) with the 3/8” Nylon Locknut (50).

18

46

 

 

 

76

 

 

 

24

 

55

 

6

25

 

 

50

 

75

47

 

 

60

 

 

90

 

75

 

 

 

25

63

 

24

 

 

48

7

 

 

 

 

60

25

 

 

24

 

25

50

 

 

 

24

75

 

8

 

49

 

 

 

2

 

 

 

62

 

 

50

 

 

75

Image 18
Contents QUESTIONS? Model No. IMSY59300 Serial NoCustomer HOT Line Table of Contents Limited WarrantyImportant Precautions Before YOU Begin For your benefit, read this manual carefully beforeDecal Assembly Make Assembly EasierFrame Assembly Nylon Locknuts yetDo not tighten the Nylon Locknuts yet Large Pin Groove Locate and open the parts bag labeled ARM Assembly Tighten the Nylon Locknuts used in stepsPage Cable Assembly Page Page Weight Cable is in the groove of the Pulley Page Page Locknut yet Page Seat Assembly Locate and open the parts bag labeled Seat AssemblyPage Adjustments Changing the Weight SettingAttaching the LAT BAR or AB Strap to High Pulley Station Adjusting the Backrest Adjusting the Curl PADAttaching the AB Strap to the AB Pulley Station Weight Resistance Chart PlatesTROUBLE-SHOOTING and Maintenance Tightening the CablesCable Diagrams Weight Cable Cable ID Stack Low Pulley Part Identification CHART-Model No. IMSY59300 R0801A X 4 Bolt X 4 3/4 Bolt X 5 1/2 Bolt 2 Square Inner Cap 3 Inner Cap 2 x 2 1/2 Inner Cap Part LIST-Model No. IMSY59300 Key No. Qty DescriptionExploded Ordering Replacement Parts