Image 8.0 user manual Do not tighten the Nylon Locknuts yet

Page 7

4.Attach the Butterfly Seat Frame (14) to the Butterfly Upright (1) with two 3/8” x 3 1/4” Bolts (62), two 3/8” Flat Washers (48), and two 3/8” Nylon Locknuts (50).

Attach the Butterfly Seat Frame (14) to the Butterfly Front Leg (3) with two 3/8” x 3 1/4” Bolts (62), two 3/8” Flat Washers (48) and two 3/8” Nylon Locknuts (50).

Do not tighten the Nylon Locknuts yet.

5.Press a 2 1/2” Square Inner Cap (76) into the Press Front Leg (20).

Attach the Press Front Leg (20) to the indicated 3/8” x 2” Carriage Bolts (92) on the Press Base (6) with two 3/8” Nylon Locknuts (50). Do not tighten the Nylon Locknuts yet. Make sure that the Press Front Leg is turned so that the indicated hole is on the side shown.

6.Attach the Press Seat Frame (7) to the Press Upright (2) with two 3/8” x 3 1/4” Bolts (62), two 3/8” Flat Washers (48), and two 3/8” Nylon Locknuts (50).

Attach the Press Seat Frame (7) to the Press Front Leg (20) with two 3/8” x 3 1/4” Bolts (62), two 3/8” Flat Washers (48), and two 3/8” Nylon Locknuts (50).

Do not tighten the Nylon Locknuts yet.

7.Insert three 1 1/2” x 2 1/2” Inner Caps (83) into the ends of the Butterfly Top Frame (33).

Attach the Butterfly Top Frame (33) to the Butterfly Upright (1) with two 3/8” x 2 1/2” Bolts (87), a Support Plate (94), and two 3/8” Nylon Locknuts (50). Do not tighten the Nylon Locknuts yet.

7

4

 

50

 

 

 

 

62

1

 

50

 

 

 

48

50

14

 

 

 

50

 

 

 

 

48

 

 

3

 

 

 

 

62

5

 

 

 

 

76

 

 

Hole

 

 

 

20

50

 

 

 

 

 

50

 

 

 

 

 

6

 

 

92

 

6

 

50

 

 

 

 

 

7

 

48

 

50

 

 

 

 

62

 

 

50

 

 

50

 

48

 

 

2

 

 

 

48

 

 

 

20

 

 

62

 

 

 

 

48

 

 

7

 

33

87

 

 

 

 

 

 

83

 

83

 

 

94

 

 

 

 

 

83

 

 

50

 

 

 

1

50

Image 7
Contents Model No. IMSY59300 Serial No QUESTIONS?Customer HOT Line Limited Warranty Table of ContentsImportant Precautions For your benefit, read this manual carefully before Before YOU BeginDecal Make Assembly Easier AssemblyNylon Locknuts yet Frame AssemblyDo not tighten the Nylon Locknuts yet Large Pin Groove Tighten the Nylon Locknuts used in steps Locate and open the parts bag labeled ARM AssemblyPage Cable Assembly Page Page Weight Cable is in the groove of the Pulley Page Page Locknut yet Page Locate and open the parts bag labeled Seat Assembly Seat AssemblyPage Changing the Weight Setting AdjustmentsAttaching the LAT BAR or AB Strap to High Pulley Station Adjusting the Curl PAD Adjusting the BackrestAttaching the AB Strap to the AB Pulley Station Plates Weight Resistance ChartTightening the Cables TROUBLE-SHOOTING and MaintenanceCable Diagrams Weight Cable Cable ID Stack Low Pulley Part Identification CHART-Model No. IMSY59300 R0801A X 4 Bolt X 4 3/4 Bolt X 5 1/2 Bolt 2 Square Inner Cap 3 Inner Cap 2 x 2 1/2 Inner Cap Key No. Qty Description Part LIST-Model No. IMSY59300Exploded Ordering Replacement Parts