JVC LVT1344-003A Connecting a Computer, Select USB in as the source Set the volume to minimum

Page 12

Connecting a Computer

This unit is equipped with a USB AUDIO terminal on the front panel.

You can connect your PC to this terminal and enjoy sound reproduced through your PC.

When you connect your PC for the first time, follow the procedure below.

•Remember you cannot send any signal or data to your PC from this unit.

IMPORTANT:

•Check if your PC equipped with the CD-ROM drive is running on Windows® 98*, Windows® Me* or Windows® XP* and prepare its CD-ROM.

How to install the USB drivers

The following procedure is described using the English version of Windows® XP. If your PC is running on a different version of operation system or language, the screens shown on your PC’s monitor will differ from the ones used in the following procedure.

1Turn on your PC and start running Windows® 98, Windows® 98 SE, Windows® Me, Windows® 2000, or Windows® XP.

•If the PC has been turned on, quit all the applications now running.

2Select “USB IN” as the source.

3Set the volume to minimum.

IMPORTANT:

•Always set volume to “VOL MIN” when connecting or disconnecting the other equipment.

4Connect the unit to the PC using a USB cable (not supplied).

Your PC automatically recognizes this connection.

Now PC is ready for playback through the USB connection.

After installation is completed, you can use your PC as the playback source. The PC automatically recognizes the unit whenever a USB cable is connected between the PC and the unit while the unit is turned on.

•When not using the PC as the playback source, disconnect the USB cable.

To play back sounds on the PC, refer to the manuals supplied with the sound reproduction application installed in the PC.

•DO NOT turn off the unit or disconnect the USB cable while installing the drivers and for several seconds while your PC is recognizing the receiver.

•Use a full speed USB cable (version 1.1). Recommended cord length is 1.5 m.

•If your PC does not recognize the unit, disconnect the USB cable and connect it again. If it does not work yet, restart Windows.

•The installed drivers can be recognized only when the USB cable is connected between the unit and your PC.

•The sound may not be played back correctly—interrupted or degraded—due to your PC settings and PC specifications.

*Microsoft®, Windows® 98, Windows® SE, Windows® Me, Windows® 2000, and Windows® XP are registered trademarks of Microsoft corporation.

PC

USB cable

• Use “USB series A plug to B plug” cable when connecting.

5The USB drivers are installed automatically.

9

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Instructions 24.0 kg Important for Laser Products Precautions IntroductionAbout This Manual Contents Location of the Buttons and Controls Front PanelBecome familiar with the buttons and controls on your unit Front Panel Display WindowSee pages in the parentheses for details Remote Control Remote ControlRhythm AX button 11 s Beep button Volume +/- button Connecting Antennas Getting StartedUnpacking FM antennaConnecting Speakers Release the finger from the clampAM antenna Connecting Other Equipment Canceling the Display DemonstrationSaving the Power Consumption while on Standby-ECO mode On the unit onlyConnecting a Computer Select USB in as the source Set the volume to minimumConnect the unit to the PC using a USB cable not supplied USB drivers are installed automaticallyTurning On or Off the Power Setting the ClockCommon Operations Selecting the SourcesAdjusting the Volume Enjoying the Powerful Sound-RHYTHM AXOn the remote control Reinforcing the Bass SoundSelecting the Sound Modes Turning On or Off the Key-touch ToneTuning in to a Station-Auto Search Tuning in to a Preset Station Presetting StationsPress SET/RESUME on the remote control again Listening to the RadioPlaying Back CDs Loading discsContinuous Playback Track mode Group modeWhen the MP3 playback mode is the Group mode See also To stop during play, press For Audio CDBasic CD Operations Changing the MP3 Playback Mode On the remote control onlyTo go to another track directly using the number buttons Turning On or Off the Resume Play for MP3 DiscOn the remote control only Load discs Programming the Playing Order of the Tracks -Program PlayPress the number buttons to select the track number Program other tracks you wantTo stop and cancel Random play, press To cancel the prohibition and unlock the carrousel, pressPlaying at Random-Random Play Repeating Tracks or CDs-Repeat PlayUsing the Timers Using Daily TimerPress CLOCK/TIMER again Set the on-time you want the unit to turn onUsing Sleep Timer Troubleshooting SymptomMaintenance Cleaning the unitHandling discs Specifications MX-GC5 Compact Component System
Top Page Image Contents