Bushnell 119628C instruction manual Installing the Batteries and SD Card, Loading Batteries

Page 6

INSTALLING THE BATTERIES AND SD CARD

Before you begin learning how to use your Trophy Cam, you will first need to install a set of batteries and insert an SD card. Although that may only take you a minute, there are some important notes about both batteries and SD cards you should be aware of, so please take the time to read the following directions and cautions:

Loading Batteries

After opening the two latches on the right side of the Trophy Cam, you will see that the Trophy Cam has eight battery slots. Starting at the top of the battery compartment, slots 1, 2, 3 and 4 form one group, while slots 5, 6, 7 and 8 form the other group, each providing 6 volts in parallel. For maximum battery life, you should install a full set of eight batteries. The Trophy Cam may also be operated by just four batteries installed in the top group only (see right), starting at slot 1. Battery life will be shorter with 4 batteries, but the camera will operate normally. Whether you use 4 or 8, be sure to insert each battery with correct

polarity (negative or “flat” end against the long spring of each battery slot). Bushnell recommends using eight new lithium AA (Energizer® brand) or alkaline AA batteries. NiMh Rechargeable batteries can also be used, but they might have a shorter life span due to their reduced efficiency over time and at low temperature. It is also possible to use a lead-acid external battery cell with 6V output or suitable AC adapter-see below for more details.

Using an External Power Source (optional, user provided)

Optionally, you can connect an external 6V DC power source to the “DC In” jack at the bottom of the Trophy Cam. It is recommended to use a power source with a current output greater than 1000mA. However, during bright daytime operation when no flash is required, the Trophy Cam can function with much less current (>400mA). Please use a compatible power source cable (not provided) to connect the external DC power source with the power input jack of the Trophy Cam, making sure that the polarity is correct. Note: The power connector is a 4.0x1.7mm coaxial DC power plug with positive “tip” (inside pin) polarity (Radio Shack P/N 274-1532 or equivalent).

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents S T R U C T I O N M a N U a L Important Note Introduction About the Trophy CamApplications Parts and Controls Back ViewFront View Installing the Batteries and SD Card Using an External Power Source optional, user providedLoading Batteries Inserting the SD Card OFF Mode Using the Trophy CAMOFF, ON, and Setup Modes On ModeSetup Mode Setup Mode Shortcut Keys/FunctionsSetup Information Screen Camera Still Photo Mode Using the Setup Menu to Change Settings Changing Parameter Settings in Setup ModePress OK to confirm and execute the new setting Parameter DisplayEXAMPLES-Changing the Settings of Some Common Parameters Field Scan 2x with Live Trigger Feature Page Select Field Scan a press OKStart times Select Field Set Field Setup Menu Parameters and Settings Description Bold=defaultParameter Settings Description IntervalTime Stamp Input Screen See UsingCoordinate NextUsing the Coordinate Input Screen Lo W000,0000Mounting and Positioning the Trophy CAM MountingSwitching on the Camera Sensing Angle and Distance TestPlaying BACK/DELETING the PHOTOS/ Videos Reviewing Images Directly From the SD CardReviewing Images on an External Video Monitor Reviewing Images by Connecting the Camera to a Computer Deleting Photos or VideosPage Downloading the PHOTOS/VIDEOS Camera takes continuous images of no subject Troubleshooting / FAQBattery life is shorter than expected Camera stops taking images or won’t take imagesCamera won’t power up Still Photo and/or Video Quality ProblemsNight photos or videos appear too dark Date/Time Stamp not appearing on images Photos Do Not Capture Subject of InterestLCD screen powers on but no text is present LCD Screen IssuesCamera won’t retain settings Screen comes on but then powers offMoisture or Ants Inside Camera Field Scan Time Lapse not working properlyTechnical Specifications ONE Year Limited Warranty FCC Compliance Statement Bushnell Outdoor Products
Top Page Image Contents