9. | Set the console assembly on the Left and Right | 9 |
|
|
| Console |
|
| |
| Handrails (87, 88). Be careful not to pinch any |
|
|
|
|
| |||
| wires. Insert the excess Upright Wire (91) into |
|
|
|
| Assembly |
|
| |
| the Right Handrail, and insert the Console |
|
|
|
|
|
|
|
|
| Ground Wire (80) into the console assembly. |
| 88 |
|
|
|
|
| 87 |
| Attach the console assembly to the Handrails |
|
|
|
|
|
| ||
| (87, 88) with five #8 x 3/4" Screws (6). Start all |
|
|
|
|
|
|
|
|
| five Screws before tightening any of them. |
|
| 6 |
| 80 |
|
| 6 |
| See steps 4 and 6. Tighten the 3/8" Jam Nuts |
|
|
|
|
| |||
| (8). |
|
|
| 91 |
| 6 |
| 6 |
|
| 6 |
|
|
|
| |||
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
| |
10. | Apply a generous amount of the included | 10 |
|
|
|
|
|
|
|
| grease to the axles and the Cylinder Spacers |
|
|
|
|
|
|
| |
| (70). |
|
|
| 64 |
|
|
| |
| Identify an Upper Cylinder Cap (68), which has |
|
|
|
|
|
| ||
| a small hole in the center. |
|
|
|
|
| Grease |
| |
| Hold a Shock Cylinder (69) near the bracket on |
|
|
|
| 10 |
| ||
| the Right Upright (72). Make sure that the | 69 |
|
|
|
|
| 72 | |
| Shock Cylinder is positioned as shown with |
| 68 |
| 5 |
|
| ||
| the arrow facing the rear of the treadmill. | Arrow |
|
|
| 68 10 | Bracket | ||
| Attach the Shock Cylinder with a 5/16" x 5/8" |
|
| 45 |
| ||||
| Patch Bolt (5), an Upper Cylinder Cap (68), and | 3 | 90 |
|
| 5 |
|
| |
| an M8 Washer (10) as shown. Do not over- |
|
|
|
| 69 | |||
| tighten the Patch Bolt. | 11 |
|
|
|
|
|
| |
| Attach the upper end of the other Shock | 70 |
|
|
|
|
|
| |
| Cylinder (69) in the same way. |
|
|
|
| Arrow |
| ||
| With the help of a second person, raise the |
|
|
|
|
|
| ||
|
|
|
|
| Incline |
|
| ||
| Frame (45) until the incline assembly is aligned |
|
|
|
|
| 11 | ||
| with the lower ends of the Shock Cylinders (69). |
|
|
|
| Assembly |
| ||
| Attach the lower end of each Shock Cylinder |
|
|
|
|
|
|
|
|
| with a 3/8" x 2" Patch Bolt (3), a Lower Cylinder |
|
|
|
|
|
|
| 90 |
| Cap (90), a 3/8" Washer (11), and a Cylinder |
|
|
|
|
|
| 70 | |
| Spacer (70) as shown. Do not overtighten the |
|
|
|
|
|
| 3 | |
| Patch Bolts. |
|
|
|
|
|
|
| |
| Make sure that both Shock Cylinders (69) are |
|
|
|
|
|
|
|
|
| set at the same firmness level (see page 18). |
|
|
|
|
|
|
|
|
|
| 11 |
|
|
|
|
|
|
|