ProForm PFTL79510.0 warranty Top, Problem The walking belt slows when walked on

Page 27
Idler Roller Bolts
2–3 in.

Locate the Reed Switch (52) and the Magnet (50)

 

 

on the left side of the Pulley (49). Turn the Pulley

 

 

until the Magnet is aligned with the Reed Switch.

 

 

Make sure that the gap between the Magnet and

52

49

the Reed Switch is about 1/8 in. (3 mm). If nec-

essary, loosen the #8 x 3/4" Tek Screw (14), move

14

50

the Reed Switch slightly, and then retighten the

1/8 in.

 

Screw. Reattach the Motor Hood (not shown) and

 

 

run the treadmill for a few minutes to check for a

Top

 

correct speed reading.

 

 

View

 

PROBLEM: The incline of the treadmill does not change correctly

SOLUTION: a. With the key in the console, press one of the Incline buttons. While the incline is changing, re- move the key. After a few seconds, re-insert the key. The treadmill will automatically rise to the maximum incline level and then return to the minimum level. This will recalibrate the incline system.

PROBLEM: The walking belt slows when walked on

SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 15.

b. If the walking belt is overtightened, treadmill perfor- b mance may decrease and the walking belt may be- come damaged. Remove the key and UNPLUG

THE POWER CORD. Using the hex key, turn both idler roller bolts counterclockwise, 1/4 of a turn. When the walking belt is properly tightened, you should be able to lift each edge of the walking belt 2 to 3 in. (5 to 7 cm) off the walking platform. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walk- ing belt is properly tightened.

c. If the walking belt still slows when walked on, see the front cover of this manual.

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents On the WEB QUESTIONS?Model No. PFTL79510.0 Serial No Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MTTable of Contents Important Precautions Instructions Save TheseBefore YOU Begin Wrench Scissors AssemblySee the inset drawing. Tie the wire tie Make sure that the power cord is unpluggedBe careful not to pinch the Upright Tighten the Bolts yet Attach the Right Upright not shownBase Covers into place yet Attach the Right Handrail 87 in the same way Important To avoid damaging Shown. Start all four Screws, and then tighten Each of themAgain. if YOU do not Connect the CON Them All four Bolts, and then tighten eachPage Raise the Frame 56 to the position shown Page Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Console Diagram Features of the Console HOW to USE the Manual Mode HOW to Turn on the PowerPage Turn on the fan if desired Measure your heart rate if desired. Before usingHOW to USE AN Onboard Workout Select an onboard workoutStart the workout Start the workout. See on HOW to USE AN Ifit Live WorkoutSelect a user Select an iFit Live workoutRecord your workout information HOW to USE a NIKE+ ModuleInsert the Nike+ module into the console Connect your iPodInformation Mode Make sure that the audio wire is fully plugged HOW to USE the Stereo Sound SystemHOW to Lower the Treadmill for USE HOW to Fold and Move the TreadmillHOW to Fold the Treadmill HOW to Move the TreadmillTroubleshooting Problem The power turns off during useCompatible with GFCI-equipped outlets Top Problem The walking belt slows when walked onProblem Solution Exercise Frequency Exercise GuidelinesExercise Intensity Workout GuidelinesR1010A Part LIST-Model No. PFTL79510.0Qty Exploded Drawing A-Model No. PFTL79510.0 R1010A Exploded Drawing B-Model No. PFTL79510.0 R1010A Exploded Drawing C-Model No. PFTL79510.0 R1010A Exploded Drawing D-Model No. PFTL79510.0 R1010A Ordering Replacement Parts Limited WarrantyIcon Health & Fitness, Inc., 1500 S W., Logan, UT
Top Page Image Contents