ProForm PFTL79510.0 warranty Troubleshooting, Compatible with GFCI-equipped outlets

Page 26

TROUBLESHOOTING

Most treadmill problems can be solved by following the simple steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, see the front cover of this manual. PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor

is plugged into a properly grounded outlet (see page 15). Use only a single-outlet surge suppres-

sor that meets all of the specifications described on page 15. IMPORTANT: The treadmill is not

compatible with GFCI-equipped outlets.

 

 

b. After the power cord has been plugged in, make sure that the key is inserted into the console.

c. Check the power switch located on the treadmill

c

 

frame near the power cord. If the switch protrudes

 

as shown, the switch has tripped. To reset the

Tripped

Reset

switch, wait for five minutes and then press the

switch back in.

 

 

PROBLEM: The power turns off during use

 

 

SOLUTION: a. Check the power switch (see the drawing above). If the switch has tripped, wait for five minutes and then press the switch back in.

b.Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c.Remove the key from the console. Reinsert the key into the console.

d.If the treadmill still will not run, please see the front cover of this manual.

PROBLEM: The console displays remain lit when you remove the key from the console

SOLUTION: a. The console features a display demo mode, designed to be used if the treadmill is displayed in a

store. If the displays remain lit when you remove the key, the demo mode is turned on. To turn off

the demo mode, hold down the Stop button for a few seconds. If the displays are still lit, see THE

INFORMATION MODE on page 23 to turn off the demo mode.

 

 

PROBLEM: The displays of the console do not function properly

 

 

 

SOLUTION: a. Remove the key from the console and UNPLUG

a

 

 

THE POWER CORD. Remove the three #8 x 1/2"

65

1

Screws (1) and the two #8 x 3/4" Screws (2).

 

Carefully pivot the Motor Hood (65) off.

2

 

 

 

 

 

 

 

 

2

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MT QUESTIONS?Model No. PFTL79510.0 Serial No On the WEBTable of Contents Important Precautions Save These InstructionsBefore YOU Begin Assembly Wrench ScissorsMake sure that the power cord is unplugged See the inset drawing. Tie the wire tieBase Covers into place yet Be careful not to pinch the UprightTighten the Bolts yet Attach the Right Upright not shown Attach the Right Handrail 87 in the same way Again. if YOU do not Connect the CON Important To avoid damagingShown. Start all four Screws, and then tighten Each of them All four Bolts, and then tighten each ThemPage Raise the Frame 56 to the position shown Page PRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Console Diagram Features of the Console HOW to Turn on the Power HOW to USE the Manual ModePage Measure your heart rate if desired. Before using Turn on the fan if desiredStart the workout HOW to USE AN Onboard WorkoutSelect an onboard workout Select an iFit Live workout HOW to USE AN Ifit Live WorkoutSelect a user Start the workout. See onConnect your iPod HOW to USE a NIKE+ ModuleInsert the Nike+ module into the console Record your workout informationInformation Mode HOW to USE the Stereo Sound System Make sure that the audio wire is fully pluggedHOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill HOW to Lower the Treadmill for USECompatible with GFCI-equipped outlets TroubleshootingProblem The power turns off during use Problem The walking belt slows when walked on TopProblem Solution Workout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencyPart LIST-Model No. PFTL79510.0 R1010AQty Exploded Drawing A-Model No. PFTL79510.0 R1010A Exploded Drawing B-Model No. PFTL79510.0 R1010A Exploded Drawing C-Model No. PFTL79510.0 R1010A Exploded Drawing D-Model No. PFTL79510.0 R1010A Icon Health & Fitness, Inc., 1500 S W., Logan, UT Ordering Replacement PartsLimited Warranty
Top Page Image Contents