ProForm PFTL79510.0 warranty Raise the Frame 56 to the position shown

Page 13

16. Make sure that there is a piece of cardboard

16

 

 

below the rear of the Frame (56).

 

 

See page 15 and plug in the power cord. Next,

 

 

 

see page 17 and turn on the power. The incline

 

 

 

system will automatically calibrate and the

 

 

 

Frame (56) will move upward and downward.

 

 

 

If the incline system does not automatically cali-

 

 

 

brate, see step 4 on page 18 and press the

 

 

 

Incline increase button until the incline is at 0

 

 

 

percent.

 

 

 

When the Frame (56) stops moving, remove the

 

 

 

key from the console and unplug the power cord.

56

 

Cardboard

 

 

17. IMPORTANT: Before you begin this step,

17

 

 

make sure that you have calibrated the

 

 

incline system as described in step 16.

56

 

 

Raise the Frame (56) to the position shown.

 

 

Have a second person hold the Frame until

 

 

 

this step is completed.

12

6

 

Orient the Storage Latch (53) so that the large

 

barrel and the latch knob are oriented as shown.

 

 

 

Attach the upper end of the Storage Latch (53)

 

 

53

to the bracket on the Frame (56) with a 3/8" x

Latch

 

1 3/4" Bolt (6) and a 3/8" Nut (12).

 

 

Attach the lower end of the Storage Latch (53) to

Knob

 

 

the Base (94) with a 3/8" x 2" Bolt (3) and a 3/8"

Large

 

 

Nut (12). Note: It may be necessary to move the

Barrel

 

 

Frame (56) back and forth to align the Storage

 

 

 

Latch with the Base.

 

 

 

 

94

12

3

 

13

 

 

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Model No. PFTL79510.0 Serial No QUESTIONS?Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MT On the WEBTable of Contents Important Precautions Instructions Save TheseBefore YOU Begin Wrench Scissors AssemblySee the inset drawing. Tie the wire tie Make sure that the power cord is unpluggedTighten the Bolts yet Attach the Right Upright not shown Be careful not to pinch the UprightBase Covers into place yet Attach the Right Handrail 87 in the same way Shown. Start all four Screws, and then tighten Each of them Important To avoid damagingAgain. if YOU do not Connect the CON Them All four Bolts, and then tighten eachPage Raise the Frame 56 to the position shown Page HOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Console Diagram Features of the Console HOW to USE the Manual Mode HOW to Turn on the PowerPage Turn on the fan if desired Measure your heart rate if desired. Before usingSelect an onboard workout HOW to USE AN Onboard WorkoutStart the workout Select a user HOW to USE AN Ifit Live WorkoutSelect an iFit Live workout Start the workout. See onInsert the Nike+ module into the console HOW to USE a NIKE+ ModuleConnect your iPod Record your workout informationInformation Mode Make sure that the audio wire is fully plugged HOW to USE the Stereo Sound SystemHOW to Fold the Treadmill HOW to Fold and Move the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USEProblem The power turns off during use TroubleshootingCompatible with GFCI-equipped outlets Top Problem The walking belt slows when walked onProblem Solution Exercise Intensity Exercise GuidelinesWorkout Guidelines Exercise FrequencyR1010A Part LIST-Model No. PFTL79510.0Qty Exploded Drawing A-Model No. PFTL79510.0 R1010A Exploded Drawing B-Model No. PFTL79510.0 R1010A Exploded Drawing C-Model No. PFTL79510.0 R1010A Exploded Drawing D-Model No. PFTL79510.0 R1010A Limited Warranty Ordering Replacement PartsIcon Health & Fitness, Inc., 1500 S W., Logan, UT
Top Page Image Contents