ProForm PFTL91105.0 user manual Troubleshooting, Problem The power turns off during use

Page 26

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please see the front cover of this manual.

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 12). Use only a single-outlet surge suppres- sor that meets all of the specifications described on page 12. Important: The treadmill is not com- patible with GFCI-equipped outlets.

b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.

c.Check the reset/off circuit breaker located on the treadmill frame near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes, and then press the switch back in.

c

Tripped

Reset

PROBLEM: The power turns off during use

SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b.Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c.Remove the key from the console. Reinsert the key into the console.

d.If the treadmill still will not run, see the front cover of this manual.

PROBLEM: The incline of the treadmill does not change correctly

SOLUTION: a. With the key in the console, press one of the Incline buttons. While the incline is changing, re- move the key. After a few seconds, re-insert the key. The treadmill will automatically rise to the maximum incline level and then return to the minimum level. This will recalibrate the incline system.

PROBLEM: The display of the console does not function properly

SOLUTION: a. Remove the key from the console and UNPLUG THE POWER CORD. With the help of a second person, carefully tip the Uprights (84) down as shown. Next, remove the three Screws (3) and the three Hood Screws (7). Note: A phillips screwdriver with a shaft at least 5” long is required.

a

3

7

 

 

3

 

 

84

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Call TOLL-FREE QUESTIONS?Model No. PFTL91105.0 Serial No Table of Contents Important Precautions Page Power Lines Before YOU Begin Back Right SideAssembly Make sure that the power cord is unpluggedBolts and then firmly tighten them Knob Spring Collar Pin Bracket Cylinder Holes Ohm Antenna HOW to Connect a VCR HOW to Connect AN AntennaHOW to Connect a 75 OHM Catv Cable PRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Features of the Console HOW to Turn on the Power HOW to USE the Manual ModeMeasure your heart rate if desired Turn on the fan if desiredHOW to USE a Preset Program Select a preset programFollow your progress with the displays Select a heart rate program HOW to USE a Heart Rate ProgramPut on the chest pulse sensor Follow your progress with the displays HOW to Create a Custom Program Select a custom programHOW to USE a Custom Program HOW to USE the Information Mode HOW to Operate the Personal TelevisionPress the Volume VOL. buttons to adjust Turn on the televisionPress the On/Off button again and add or Delete channels Optional Chest Pulse SensorHOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useProblem The walking belt slows when walked on Top Problem Television reception is poor Workout Guidelines Conditioning GuidelinesExercise Intensity Exercise FrequencySuggested Stretches R0506A Qty DescriptionExploded DRAWING-Model No. PFTL91105.0 104 67 82 Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT Ordering Replacement PartsLimited Warranty
Top Page Image Contents