ProForm PFTL91206.0 user manual

Page 8

4.With the help of a second person, carefully tip the Uprights (109) down to the position shown. Make sure that the Extension Legs (105) remain in the Uprights.

Attach each Extension Leg (105) with two 3/4” Tek Screws (47) and a Round Base Pad (121) as shown. Note: Attach the lower Tek Screw (without the Round Base Pad) first.

Attach a Wheel (108) to each Wheel Housing (106) with a Wheel Bolt (107) and a Wheel Nut (21). Make sure that the Wheel Bolts are inserted from the outside as shown. Do not overtighten the Wheel Bolts.

With the help of a second person, carefully raise the Uprights (109) so the Wheels (108) touch the floor.

5.Remove the knob from the pin. Make sure that the collar and the spring are on the pin. Insert the pin into the Latch Housing (75), and tighten the knob back onto the pin.

Raise the Frame (54) to the vertical position. While another person holds the Frame, hold the Latch Housing (75) against the inside of the Frame. Thread two 3/4” Screws

(6) several turns into the Latch Housing and the Frame.

Align the pin with the hole in the Left Handgrip (76) by sliding the Latch Housing (75) up or down. Make sure that the pin can be inserted fully into the hole. Hold the Latch Housing in place and tighten the two 3/4” Screws (6). Be careful not to overtighten the Screws.

Pull the knob to the right and carefully lower the Frame (54) to the floor.

Note: After a period of use, the Latch Housing (75) may need to be adjusted again to align the pin with the hole in the Left Handgrip (76).

4

 

106

108

 

109

21

107

 

 

 

 

 

 

21

 

 

106

 

 

121

107

 

 

 

108

 

 

 

 

 

 

 

47

 

 

105

 

 

 

121

 

 

 

47

 

 

 

105

 

5

 

 

 

 

 

 

76

 

 

Hole

 

 

 

Pin

Collar

 

 

 

75

 

 

54

6

 

 

 

 

 

Spring

 

 

 

Knob

6.Make sure that all parts are properly tightened before you use the treadmill. Note: Extra hardware may be included. Keep the included hex keys in a secure place; the large hex key is used to adjust the walking belt (see page 22). To protect the floor or carpet, place a mat under the treadmill.

8

Image 8
Contents Call TOLL-FREE QUESTIONS?Model No. PFTL91206.0 Serial No Table of Contents Important Precautions Page Right Side Before YOU BeginBack Assembly Bolts, tighten them Page Page PRE-LUBRICATED Walking Belt HOW to Plug in the Power CordTreadmill Operation Features of the Console HOW to Turn on the Power HOW to USE the Manual ModeSpeed display-This Calories/PulseTime/Pace display Measure your heart rate if desiredPress the Start button to start the program HOW to USE a Preset ProgramSelect a preset program Monitor your progress with the displays HOW to USE a Heart Rate Program Select a heart rate programMonitor your progress with the displays Information MODE/DEMO Mode Optional Chest Pulse SensorHOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useProblem The walking belt slows when walked on Top ViewExercise Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencySuggested Stretches Page R0906A Qty DescriptionDescription Exploded Exploded Drawing B-Model No. PFTL91206.0 R0906A Exploded Drawing C-Model No. PFTL91206.0 R0906A Exploded Drawing D-Model No. PFTL91206.0 R0906A Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT Ordering Replacement PartsLimited Warranty