ProForm PFTL49609.0 user manual Make sure that no wires are pinched

Page 12

12. Raise the Frame (51) to the position shown.

12

 

 

Have a second person hold the Frame until

51

 

this step is completed.

 

 

Orient the Storage Latch (48) so that the large

 

 

 

barrel and the Latch Knob (49) are in the posi-

8

 

4

tions shown. Attach the lower end of the Storage

 

Latch to the bracket on the Base (86) with a 3/8"

 

 

 

x 2" Bolt (4) and a 3/8" Nut (8).

 

 

48

Attach the upper end of the Storage Latch (48)

49

 

 

 

to the bracket on the Frame (51) with a 3/8" x 2"

 

 

Large

Bolt (4) and a 3/8" Nut (8). Note: It may be nec-

 

 

essary to move the Frame back and forth to

 

 

Barrel

align the Storage Latch with the bracket.

 

 

86

Lower the Frame (51) (see HOW TO LOWER

 

 

THE TREADMILL FOR USE on page 21).

 

8

 

 

 

4

 

 

 

13.Make sure that all parts are properly tightened before you use the treadmill. If there are sheets of clear plastic on the treadmill decals, remove the plastic. To protect the floor or carpet, place a mat under the tread- mill. Note: Extra hardware may be included. Keep the included hex key in a secure place; the hex key is used to adjust the walking belt (see pages 23 and 24).

If you purchase the optional chest pulse sensor (see page 19), follow the steps below to install the re- ceiver included with the chest pulse sensor.

1. Make sure that the power cord is unplugged.

 

96

 

Remove the indicated 4.2 x 16mm Screw (3)

 

 

and the Access Door (105) from the Console

 

 

 

Base (96).

 

 

 

2. Connect the wire on the receiver to the indi-

 

 

 

cated wire extending from the Console Base

 

 

 

(96). Hold the receiver so the antenna is ori-

 

 

 

ented as shown and is facing the Console

 

 

 

Base. Attach the receiver to the plastic posts on

Small

 

Wire

the Access Door (105) with the two included

 

small screws.

Screws

 

Receiver

3. Make sure that no wires are pinched.

Antenna

 

 

Reattach the Access Door (105) with the #8 x

 

 

105

3/4" Screw (12). Discard the other wires in-

 

3

cluded with the receiver.

 

 

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents QUESTIONS? Model No. PFTL49609.0 Serial NoMon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MT On the WEBTable of Contents Important Precautions Page Before YOU Begin Assembly Wheel must turn freely Page Wheel must turn freely Firmly tighten the Bolts Again. if the Connectors are not CON Be Damaged When YOU Turn on109, 110. Make sure that the wires are not Nected PROPERLY, the Console MAYMake sure that no wires are pinched Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Console Diagram Features of the ConsoleHOW to Turn on the Power HOW to USE the Manual ModeInsert the key into the console Start the walking beltMeasure your heart rate if desired HOW to USE the Weight Loss Center Select a calorie goal workoutHOW to USE a Classic Workout HOW to USE the Stereo Sound System Information ModeOptional Chest Pulse Sensor HOW to Fold and Move the Treadmill HOW to Move the TreadmillHOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useCompatible with GFCI-equipped outlets Problem The walking belt slows when walked on TopProblem Solution Exercise Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencyPart LIST-Model No. PFTL49609.0 Key No. Qty DescriptionQty Exploded Drawing A-Model No. PFTL49609.0 R0310A Exploded Drawing B-Model No. PFTL49609.0 Exploded Drawing C-Model No. PFTL49609.0 R0310A Exploded Drawing D-Model No. PFTL49609.0 R0310A Ordering Replacement Parts Limited WarrantyIcon Health & Fitness, Inc., 1500 S W., Logan, UT
Top Page Image Contents