JVC RX-6020VBK manual Operating JVC’s Audio/Video Components, Operating Audio Components

Operating JVC’s Audio/Video Components

English

You can use the remote control to operate other JVC’s components.

Operating Audio Components

IMPORTANT:

To operate JVC’s audio components using this remote control:

•You need to connect JVC’s audio components through the COMPU LINK (SYNCHRO) jacks (see page 25) in addition to the connections using cables with RCA pin plugs (see page 6).

•Aim the remote control directly at the remote sensor on the receiver.

•If you use the buttons on the front panel, the remote control will not operate that source. To operate a source with the remote control, the source must be selected with source selecting buttons on the remote control.

•To operate the cassette deck or CD recorder by COMPU LINK remote control system, set the source name correctly. (See page 8.)

•Refer also to the manuals supplied with your audio components.

Sound Adjustment

You can always use following buttons for sound adjustment:

SURROUND ON/OFF : Turn on or off Surround modes.

SURROUND MODE : Select Surround modes.

After pressing SOUND, you can use following buttons for sound adjustment:

SUBWOOFER +/–	: Adjust the subwoofer output level.
CENTER +/–	: Adjust the center speaker output level.
REAR•L +/–	: Adjust the left rear speaker output level.
REAR•R +/–	: Adjust the right rear speaker output level.
EFFECT	: Select the DAP effect level.
TEST	: Turn on or off the test tone output.

Note:

After adjusting sounds, press the corresponding source selecting button or CD-DISC to operate your target source with 10 keys on the remote control, otherwise 10 keys cannot be used for operating your target source.

CD player

After pressing CD, you can use following buttons for CD operations:

3	: Start playback.
4	: Return to the beginning of the current
	(or previous) track.
¢	: Skip to the beginning of the next track.
7	: Stop playback.
8	: Pause playback. To release it, press 3.
1 – 10, +10	: Select a track number directly.
	• For track number 5, press 5.
	• For track number 15, press +10, then 5.
	• For track number 20, press +10, then 10.

CD changer

After pressing CD-DISC, you can use following buttons for CD changer operations:

3	: Start playback.
4	: Return to the beginning of the current
	(or previous) track.
¢	: Skip to the beginning of the next track.
7	: Stop playback.
8	: Pause playback. To release it, press 3.
1 – 6, 7/P	: Select the number of a disc installed in a CD
	changer.

If your CD changer is of 200-disc loading capability (except for

XL-MC100 and XL-MC301),you can do following operations with number buttons after pressing CD:

1Select a disc number.

2Then select a track number (always enter two digits).

3Start playback.

Examples:

•Selecting disc number 3, track number 2, and start playback. Press 3, then, 0, 2, then 3.

•Selecting disc number 10, track number 5, and start playback. Press 1, 0, then, 0, 5, then 3.

•Selecting disc number 105, track number 12, and start playback. Press 1, 0, 5, then 1, 2, then 3.

Tuner

You can always use following buttons:

FM/AM	: Alternate between FM and AM.
FM MODE	: Change the FM reception mode.

After pressing FM/AM, you can use following buttons for Tuner operations:

1 – 10, +10: Select a preset channel number directly.

• For channel number 5, press 5.

• For channel number 15, press +10, then 5.

• For channel number 20, press +10, then 10.

CD recorder

Before starting operations described below, make sure that you have changed the source name correctly. See page 8.

After pressing TAPE/CDR, you can use following buttons for CD recorder operations:

3	: Start playback.
4	: Return to the beginning of the current
	(or previous) track.
¢	: Skip to the beginning of the next track.
7	: Stop playback or recording.
8	: Pause playback. To release it, press 3.
REC PAUSE	: Press this button to enter recording pause.

Press this button and then 3 to start recording.

28