JVC RX-6020VBK manual Speaker signal cables are not connected

Page 67

Troubleshooting

Use this chart to help you solving daily operational problems. If there is any problem you cannot solve, contact your JVC service center.

PROBLEM

POSSIBLE CAUSE

SOLUTION

 

 

 

The power does not turn on.

The power cord is not plugged in.

Plug the power cord into an AC outlet.

No sound from speakers.

Speaker signal cables are not connected.

Check speaker wiring and reconnect if necessary.

The SPEAKERS ON/OFF button is not set correctly.

Press SPEAKERS ON/OFF button correctly.

An incorrect source is selected.

Select the correct source.

 

 

Muting is activated.

Press MUTING to cancel the mute.

An incorrect input mode (analog or digital) is selected.

Select the correct input mode (analog or digital).

Connections are incorrect.

Check connections.

 

For analog connections, see page 6.

 

For digital connections, see page 7.

Sound from one speaker only.

Speaker signal cables are not connected properly.

Check speaker wiring and reconnect if necessary.

 

The balance is set to one extreme.

Adjust the balance properly (see page 15).

 

 

 

Continuous hiss or buzzing during FM

Incoming signal is too weak.

Connect an outdoor FM antenna or contact

reception.

 

your dealer.

 

 

 

 

 

 

The station is too far away.

Select a new station.

 

 

 

 

 

An incorrect antenna is used.

Check with your dealer to be sure you have the

 

 

correct antenna.

 

 

 

 

 

 

Antennas are not connected properly.

Check connections.

 

 

 

 

Occasional cracking noise during FM

Ignition noise from automobiles.

Move the antenna farther from automobile

reception.

 

traffic.

 

 

 

 

 

 

“OVERLOAD” starts flashing on the

Speakers are overloaded because of high

1.

Press STANDBY/ON

on the front

display.

volume.

 

panel to turn off the receiver.

 

 

2.

Stop the playback source.

 

 

 

3.

Turn on the receiver again, and adjust the

 

 

 

volume.

 

Speakers are overloaded because of short circuit of speaker terminals.

Press STANDBY/ON on the front panel, then check the speaker wiring.

If “OVERLOAD” does not disappear, unplug the AC power cord, then plug it back again.

If speaker wiring is not short-circuited, contact your dealer.

“DSP MICON NG” starts flashing on the

The built-in microcomputer is not

Press STANDBY/ON

on the front panel to

display.

functioning correctly.

turn off the receiver. After unplugging the

 

 

power cord, consult your dealer.

 

 

 

 

The STANDBY lamp lights up after

The receiver is overloaded because of a

Press STANDBY/ON

on the front panel to

turning on the power, but soon the

high voltage.

turn off the receiver. After unplugging the

receiver turns off (into standby mode).

 

power cord, consult your dealer.

 

 

 

 

Remote control does not work.

There is an obstruction in front of the

Remove the obstruction.

remote sensor on the receiver.

 

 

Batteries are weak.

Replace batteries.

 

 

 

Remote control does not work for the source (or other components) you try to operate.

An incorrect remote control operation mode is selected.

Select the correct remote control operation mode (see pages 28 and 29).

30

Page 66 Page 68
Image 67
Page 66 Page 68
Contents RX-6020VBK Recepteur DE Control AUDIO/VIDEO Mises en garde, précautions et indications diverses Table of Contents Parts Identification Remote ControlFront Panel Replace the cover Before Installation Putting Batteries in the Remote ControlChecking the Supplied Accessories Getting StartedSupplied FM Standard type Connecting the FM and AM AntennasAM loop antenna connection FM antenna connectionConnecting the subwoofer speaker Connecting the SpeakersConnecting the front, center and rear speakers Speaker layout diagramVideo component connections Connecting Audio/Video ComponentsTurn off all components before connecting Analog connections Audio component connectionsDigital connections Connecting the Power CordFor enjoying DVD Multi Playback Mode Plug the power cord into an AC outletSelecting the Source to Play Turning On the PowerTo turn off the power into standby mode Basic OperationsOn the front panel Adjusting the VolumeFrom the remote control Changing the source nameTemporarily-Muting Turning Off the PowerWith the Sleep Timer Turning Off the SoundsSelecting the Analog or Digital Input Mode Basic SettingsTo register whether you have Connected a subwoofer or not Setting the Speaker Information RemoteOn the front panel From the remote control Press ANALOG/DIGITALTo select the appropriate speaker Distance Unit with the current setting Appears on the displayPress Control UP /DOWN Select the unitSelect the low frequency effect attenuator level Press Setting repeatedly until LFEComp Dynamic range DisplayAdjusting the Subwoofer Output Level Sound AdjustmentsUsing Preset Tuning Tuning in StationsTuner Operations Selecting the FM Reception Mode Typical Multichannel 5.1 ch reproduction Creating Realistic Sound FieldsDolby Surround DTS Digital SurroundAll Channel Stereo DVD Multi Playback ModeDAP Digital Acoustic Processor modes Creating sound fieldTurning on or off Surround modes About Relations between Speaker Layout and Surround ModesSelecting Surround modes Rearl + Rearr + Activate Surround modeIf you like to adjust sound, go to step Press Surround ON/OFF toPanorama with the current Adjust the speaker output levels 10 to +10Repeatedly to activate Surround Mode Press Control UPUsing DAP Modes and All Channel Stereo Press DVD Multi Using DVD Multi Playback ModeActivating DVD Multi Playback Mode Adjust the speaker output levelsAutomatic Source Selection Compu Link Remote Control SystemPress the play 3 button on the CD player Synchronized RecordingConnections AV Compu Link Remote Control SystemOne Touch DVD Play Automatic Selection of TV’s Input ModeAutomatic Power On/Off One-Touch Video PlayOperating Audio Components Operating JVC’s Audio/Video ComponentsCassette deck Operating Video ComponentsDVD player Problem Possible Cause Solution TroubleshootingHarmonic distortion SpecificationsPer channel, min. RMS, driven into 8 Ω Hz to 20 kHz with no more than 0.8% totalAM tuner FM tuner IHFGeneral EN, FR 0102NHMMDWJEIN Mises en garde, précautions et indications diverses Table of Contents FM/AM Tuning 5/ ∞ up/down buttons Identification / Getting Started Rear Right Started Components Getting Started Selecting SourceButtons Basic Operations Sound through all speakers or headphones Connected Digital in Terminals Setting the Digital InputSPK Digital Auto Basic Settings Press Setting repeatedly until LFE Or Treble with the current setting Appears on the display Sound AdjustmentsMEMORYFM/AM Tuner Operations Speaker Subwoofer speaker Left rear Possible / × Impossible Creating Realistic Sound FieldsCreating Realistic Sound Fields Receiver Test Center Press Sound Using DAP Modes and All Channel Stereo Refer to the manual supplied with the DVD player Control System Using DVD Multi PlaybackAV Compu Link Remote Control System AV Compu Link Remote Select the number of a disc installed in a CD Changer Video Components Speaker signal cables are not connected Trouble Shooting / Specifications Specifications Toll Free 1 800 Do not service the television yourselfLimited Warranty 1201NHMMDWJEIN

RX-6020VBK specifications

The JVC RX-6020VBK is a versatile and robust audio/video receiver that caters to both audiophiles and casual listeners. Renowned for its dynamic performance and reliability, the RX-6020VBK is an exemplary model within JVC's lineup, blending modern technology with user-friendly features.

At the heart of the RX-6020VBK is its exceptional audio processing capabilities, which deliver a rich and immersive sound experience. It operates with a powerful amplifier that boasts a total output of 100 watts per channel. This capability allows it to drive a wide range of speakers with ease, providing clear and distortion-free audio even at higher volumes.

One of the standout features of this receiver is its support for multiple audio and video formats. The RX-6020VBK can handle various surround sound formats, including Dolby Digital and DTS, ensuring that users enjoy a cinematic experience right at home. The unit features advanced digital signal processing, providing precise control over sound characteristics and allowing users to tailor their listening experience to their preferences.

Equipped with substantial connectivity options, the RX-6020VBK integrates seamlessly into any home entertainment system. It offers multiple HDMI inputs, composite and component video connections, as well as coaxial and optical digital audio inputs. This array of options makes it easy to connect a wide range of devices, from gaming consoles to Blu-ray players. The receiver also includes an AM/FM tuner, allowing users to enjoy their favorite radio stations.

Further enhancing its usability, the JVC RX-6020VBK features an intuitive on-screen display that simplifies navigation of the receiver's extensive settings and adjustments. The remote control is ergonomically designed, providing easy access to essential functions without overwhelming the user.

In terms of build quality, the RX-6020VBK is sturdily constructed, ensuring longevity and durability. Its sleek black exterior fits well with most home décor styles, making it an aesthetically pleasing addition to any setup.

Overall, the JVC RX-6020VBK is a well-rounded audio/video receiver that combines powerful performance, versatile connectivity, and user-friendly features, making it an excellent choice for anyone looking to enhance their home entertainment experience. Whether for music listening or movie watching, this receiver stands out as a reliable choice in today's market.
Top Page Image Contents