JVC RX-6020VBK manual Sound through all speakers or headphones Connected

Basic Operations

Turning Off the Sounds	Remote
Temporarily—Muting	ONLY
You can mute the sound temporarily.
Press MUTING on the remote control to mute	MUTING
the sound through all speakers or headphones
connected.

•“MUTING” appears on the display and the volume turns off (the volume level indicator goes off).

ANALOG SPK

L C R

S.WFR LFE

LS S RS

CH-

To restore the sound, press MUTING again.

•Turning MASTER VOLUME on the front panel or pressing VOLUME +/– on the remote control also restores the sound.

Changing the Display Brightness	Remote
	ONLY
You can dim the display.
Press DIMMER on the remote control .	DIMMER
• Each time you press the button, the display dims and
brightens alternately.
Turning Off the Power	Remote
with the Sleep Timer	ONLY

You can fall asleep while listening to music—Sleep Timer.

Basic adjustment auto memory

This receiver memorizes sound settings for each source when:

•Turning off the power,

•Changing the source, and

•Assigning the source name.

When you change the source, the memorized settings for the newly selected source are automatically recalled.

Following can be stored for each source:

•Input attenuator mode (see page 15)

•Balance (see page 15)

•Tone adjustment (see page 15)

•Subwoofer output level (see page 15)

•Surround mode selection (see page 21-23)

Notes:

•You cannot assign and store different settings for digital input mode and analog input mode.

•If the source is FM or AM, you can assign a different setting for each band.

For recording

You can record any source playing through the receiver to a cassette deck (or a CD recorder) connected to the TAPE/CDR jacks and the VCR connected to the VCR jacks at the same time.

While recording, you can listen to the selected sound source at whatever sound level you like without affecting the sound levels of the recording.

Note:

The output level, tone adjustment (see page 15), and Surround

modes (see page 21-23) cannot affect the recording.

Signal and speaker indicators on the display

Signal indicators Speaker indicators

Press SLEEP on the remote control repeatedly.

SLEEP

L C R	ANALOG SPK		ONETOUCH	L C R
	DIGITAL AUTO	L C R	PROLOGIC ΙΙ

• The SLEEP indicator lights up on the display, and the shut-off time changes in 10 minutes intervals.

ANALOG	SPK		SLEEP
	L	C	R
	S.WFR LFE
	LS	S	RS

CH-

10 20 30 40 50 60

0(Canceled) 90 80 70

When the shut-off time comes

The receiver turns off automatically.

To check or change the time remaining before the shut-off time

Press SLEEP once.

The remaining time (in minutes) until the shut-off time appears.

•To change the shut-off time, press SLEEP repeatedly until preferred remaining time appears on the display.

To cancel the Sleep Timer

Press SLEEP repeatedly until “SLEEP 0 MIN” appears on the display. (The SLEEP indicator goes off.)

• Turning off the power also cancels the Sleep Timer.

	LINEAR PCM	S.WFR LFE
S.WFR LFE	DIGITAL	LS S RS	S.WFR LFE
		CH-
LS S RS			LS S RS

The following signal indicators light up—:

L: • When digital input is selected: Lights up when the left channel signal comes in.

•When analog input is selected: Always lights up.

R: • When digital input is selected: Lights up when the right channel signal comes in.

•When analog input is selected: Always lights up.

C : When the center channel signal comes in.

LS : When the left rear channel signal comes in.

RS : When the right rear channel signal comes in.

S : When the monaural rear channel signal or 2 ch Dolby Surround encoded signal comes in.

LFE: When the LFE channel signal comes in.

The speaker indicators light up when both of the following conditions are satisfied:

•The corresponding speaker is activated, and

•The corresponding speaker is required for the current playback.

Notes:

•When you select “DVD MULTI,” all signal indicators except “S” light up.

•When “SUBWOOFER” is set to “YES” (see page 12), S.WFR lights up.

10