ProForm PFTL79008.0 manual Not Connected PROPERLY, the CON Sole MAY be Damaged When

Page 10

9.

Set the console assembly face down on a soft

9

 

 

 

 

 

 

surface to avoid scratching the console assem-

 

 

 

 

 

 

bly. Remove the two #8 x 3/4" Screws (1). Lift

 

 

 

110

 

 

 

off the Pulse Bar (110). Save the Pulse Bar

 

 

1

 

 

 

and the two Screws for assembly steps 10

 

 

 

 

 

 

and 12.

 

 

 

 

 

 

 

 

 

 

 

 

Console

 

 

 

 

 

 

 

Assembly

 

10.

Set the Pulse Bar (110) on the Left and Right

10

4

 

 

 

 

 

Uprights (77, 92). Attach the Pulse Bar with four

 

 

 

 

 

#10 x 3/4" Screws (4) and four #10 Star

 

12

 

 

 

 

 

Washers (12). Start all four Screws before

 

 

 

 

 

 

firmly tightening any of them. Be careful not

 

5

 

110

 

 

 

to pinch the Wire Harness (91).

 

 

4

 

 

Firmly tighten the four 5/16" x 1 3/4" Bolts

 

 

 

 

12

 

(5).

 

 

 

 

 

 

 

 

77

 

 

5

91

 

 

 

 

 

 

 

 

 

 

 

 

92

 

11.

While a second person holds the console as-

11

 

 

Console

Console

 

 

sembly near the Pulse Bar (110), connect the

 

 

 

 

Console Ground Wire (109) on the Pulse Bar to

 

 

 

Assembly

Wire

 

 

the ground wire from the console assembly.

 

 

 

 

 

 

 

Connect the console wire to the Wire Harness

 

 

 

 

 

 

 

(91). See the inset drawing. The connectors

Ground

 

 

 

 

 

should slide together easily and snap into

 

 

91

 

 

place. If they do not, turn one connector and

 

Wire

 

 

 

 

then try again. IF THE CONNECTORS ARE

 

 

 

 

 

 

 

NOT CONNECTED PROPERLY, THE CON-

 

 

 

 

 

 

 

SOLE MAY BE DAMAGED WHEN THE

 

109

 

 

 

 

 

POWER IS TURNED ON. Lay the wires inside

 

 

 

Console Wire

 

the bottom of the Pulse Bar (110).

 

110

 

 

 

 

 

 

 

91

 

 

 

10

 

 

 

 

 

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MT QUESTIONS?Model No. PFTL79008.0 Serial No On the WEBTable of Contents Local electronics store Important PrecautionsPulse sensors are not medical devices Page Before YOU Begin Assembly Do not fully fold the Frame yet Make sure that the power cord is unpluggedTighten the Nut the Wheel must turn freely Right Upright do not fully tighten the Bolts Yet With a second Bolt Spacer 95, 3/8 x 4 Bolt 3/8 Star WasherNot fully fold the Frame yet Bolts yet Not Connected PROPERLY, the CON Sole MAY be Damaged When Screws before firmly tightening any of them WiresUprights 77, 92. Be careful not to pinch any Same wayDoes not come apart. Note See the lower Attach the other Crosswalk Arm 82Raise the Frame 48 to the position shown HOW to PUT on the Chest Pulse Sensor HOW to USE the Chest Pulse SensorChest Pulse Sensor Care and Maintenance HOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Console Diagram Features of the ConsoleSelect the manual mode. When you HOW to Turn on the PowerHOW to USE the Manual Mode Insert the key into the consoleMeasure your heart rate if desired Follow your progress with the displays. WhenTurn on the fan if desired HOW to USE a Preset Workout Select a preset workoutInformation Mode HOW to USE the Crosswalk ArmsHOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USEProblem The power turns off during use TroubleshootingCompatible with GFCI-equipped outlets Problem The walking belt slows when walked on TopProblem The crosswalk arms squeak during use Turn if the walking belt has shifted to the rightWorkout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencyPart LIST-Model No. PFTL79008.0 Key No. Qty DescriptionQty Exploded Drawing A-Model No. PFTL79008.0 R0109A Exploded Drawing B-Model No. PFTL79008.0 R0109A 10195 102 103 111 Exploded Drawing D-Model No. PFTL79008.0 R0109A Limited Warranty Ordering Replacement PartsIcon Health & Fitness, Inc., 1500 S W., Logan, UT
Top Page Image Contents