ProForm PFTL70010.0 warranty Top, View, Problem The walking belt slows when walked on

Page 26
Idler Roller Bolts
2–3 in.

Remove the three #8 x 3/4" Screws (1) and carefully

 

1

pivot the Motor Hood (61) off.

61

 

 

Locate the Reed Switch (71) and the Magnet (48)

 

 

on the left side of the Pulley (49). Turn the Pulley

 

 

until the Magnet is aligned with the Reed Switch.

1/8 in.

 

Make sure that the gap between the Magnet and

 

the Reed Switch is about 1/8 in. (3 mm). If neces-

17

 

sary, loosen the #8 x 3/4" Truss Head Screw (17),

48

move the Reed Switch slightly, and then retighten

71

the Screw. Reattach the Motor Hood (not shown)

Top

49

with the #8 x 3/4" Screws. Reattach the #8 x 2"

 

Screws, if necessary. Run the treadmill for a few

View

 

minutes to check for a correct speed reading.

 

 

PROBLEM: The incline of the treadmill does not change correctly

SOLUTION: a. With the key in the console, press one of the Incline buttons. While the incline is changing, re- move the key. After a few seconds, reinsert the key. The treadmill will automatically rise to the maximum incline level and then return to the minimum level. This will recalibrate the incline system.

PROBLEM: The walking belt slows when walked on

SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 16.

b. If the walking belt is overtightened, treadmill perfor- b mance may decrease and the walking belt may be- come damaged. Remove the key and UNPLUG

THE POWER CORD. Using the hex key, turn both idler roller bolts counterclockwise, 1/4 of a turn. When the walking belt is properly tightened, you should be able to lift each edge of the walking belt 2 to 3 in. (5 to 7 cm) off the walking platform. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walk- ing belt is properly tightened.

c. If the walking belt still slows when walked on, see the front cover of this manual.

26

Image 26
Contents Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MT QUESTIONS?Model No. PFTL70010.0 Serial No On the WEBTable of Contents Important Precautions Save These InstructionsBefore YOU Begin Assembly Wrench ScissorsPage Do not fully tighten the Bolts yet. Partially See the inset drawing. Tie the wire tieBe careful not to pinch the Upright Wire Do not fully tighten the Bolts yet. Partially Page Assembly Page Page Page Raise the Frame 53 to the position shown PRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Console Diagram Features of the Console HOW to Turn on the Power HOW to USE the Manual ModeTurn on the fan if desired Follow your progress with the displays. The matrix-When youMeasure your heart rate if desired Start the workout HOW to USE AN Onboard WorkoutSelect an onboard workout HOW to USE the Weight Loss Center Select a weight loss workoutHOW to USE AN Ifit Workout Insert an iFit card and select a workoutInformation Mode HOW to USE the Stereo Sound SystemHOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill HOW to Lower the Treadmill for USEOutlets TroubleshootingProblem The power turns off during use View Problem The walking belt slows when walked onTop Problem Solution Workout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencySuggested Stretches Part List Key No. Qty DescriptionQty Exploded Drawing a Exploded Drawing B Exploded Drawing C Exploded Drawing D Icon Health & Fitness, Inc., 1500 S W., Logan, UT Ordering Replacement PartsLimited Warranty