HOW TO TURN ON THE POWER
1 Plug in the power cord (see page 8).
2 | Locate the reset/off |
|
|
|
|
|
|
circuit breaker near |
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| the power cord. Make |
| Reset | ||||
|
|
|
|
|
| ||
| sure that the circuit |
| Position |
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| |
| breaker is in the reset |
|
|
|
|
|
|
| position. |
|
|
|
|
|
|
|
|
|
|
|
|
|
Stand on the foot rails of the treadmill. Find the clip
3 attached to the key (see the drawing on page 9), and slide the clip onto the waistband of your clothes. Next, insert the key into the console. The display will light. Important: In an emergency situation, the key can be pulled from the con- sole, causing the walking belt to slow to a stop. Test the clip by carefully taking a few steps backward; if the key is not pulled from the console, adjust the position of the clip.
HOW TO USE THE MANUAL MODE
1 Insert the key into the console.
See HOW TO TURN ON THE POWER above.
2 Select the manual mode.
When the |
|
|
|
|
|
|
|
key is in- |
|
|
|
|
|
|
|
serted, the |
|
|
|
|
|
|
|
manual |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
mode will |
|
|
|
|
|
| |
|
|
| Track |
| |||
be selected. |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
If a program |
|
|
|
|
|
|
|
has been selected, reselect the manual mode by pressing the Program Select button repeatedly until a track appears in the lower part of the dis- play and the letters “iFIT” do not appear.
3 Start the walking belt.
To start the walking belt, press the Start button, the Speed increase button, or one of the speed buttons numbered 1 through 10.
If the Start button or the Speed increase button is pressed, the walking belt will begin to move at 1 mph. As you exercise, change the speed of the walking belt as desired by pressing the Speed in-
crease and decrease buttons. Each time a button is pressed, the speed setting will change by 0.1 mph; if a
button is held down, the
speed setting will change in increments of 0.5 mph. Note: After the buttons are pressed, it may take a moment for the walking belt to reach the se- lected speed setting.
If one of the numbered speed buttons is pressed, the walking belt will gradually increase in speed until it reaches the selected speed setting.
To stop the walking belt, press the Stop button. To restart the walking belt, press the Start button, the Speed increase button, or one of the numbered buttons.
Note: The first time the treadmill is used, observe the alignment of the walking belt, and center the walking belt if necessary (see page 23).
4 Change the incline of the treadmill as desired.
To change the incline of
the treadmill, press the Incline increase and de- crease buttons. Each time a button is pressed, the incline will change by
0.5%. Note: After the buttons are pressed, it may take a moment for the treadmill to reach the se- lected incline setting.
5 Follow your progress with the display.
Note: The display can be backlit with any of five colors. To select the desired color, press the Display Color button repeatedly.
When the |
|
manual mode |
|
or the |
|
iFIT.com |
|
mode is se- | Track |
lected, the |
|
lower part of
the display will show a
10