ASSEMBLY
CAUTION: Read and follow step 1 below before removing the restraining tie (see drawing 1). If the restrain- ing tie is removed prematurely, serious bodily injury may result. Assembly requires two people. Set the tread- mill in a cleared area and remove the packing materials except for the restraining tie. Do not dispose of the packing materials until assembly is completed. Use the HARDWARE IDENTIFICATION CHART in the center of
this manual to identify the parts used in assembly. Assembly requires the included allen wrench 
, a
phillips screwdriver 
, and two adjustable wrenches 
.
1. | Slide the Left Upright (1) onto the left side of the Base | 1 |
|
|
| (59). It may be necessary to firmly push down on the |
|
| |
| 1 |
|
| |
| Left Upright until it is fully seated on the Base. |
|
|
|
| Remove the restraining tie from the Base. |
|
| Handrail |
| Attach the left handrail to the Base (59) with a Handrail | 63 |
|
|
| Bolt (93), 3/8” Washer (67), and Handrail Nut (4). Do not |
|
| |
| tighten the Handrail Bolt yet. Using the allen wrench, | 59 |
|
|
| tighten two Upright Screws (63) into the Left Upright (1) |
|
| |
|
|
|
| |
| and the Base. | Restraining Tie |
| 4 |
|
| 93 |
| 67 |
2. | Slide the Right Upright (44) onto the right side of the | 2 |
|
|
| Base (59). It may be necessary to firmly push down |
|
| |
| 9 |
|
| |
| on the Right Upright until it is fully seated on the | 25 |
|
|
| Base. Be careful not to pinch the Wire Harness (25) |
|
| |
|
|
|
| |
| between the Right Upright and the Base. |
|
|
|
| Attach the right handrail to the Base (59) with a Handrail |
|
|
|
| Bolt (93), 3/8” Washer (67), and Handrail Nut (4). Do not |
|
|
|
| tighten the Handrail Bolt yet. Using the allen wrench, |
|
| 44 |
| tighten two Upright Screws (63) into the Right Upright (44) |
|
| |
|
|
|
| |
| and the Base. |
|
|
|
| Hand tighten the Handrail Nuts (4) used in steps 1 and 2. |
|
|
|
| Using a wrench, tighten the Handrail Bolts (93) used in |
|
|
|
| steps 1 and 2. |
|
|
|
| Remove the wire ties (not shown) attaching the Console |
|
|
|
| Base (9) to the Right Upright (44). |
|
| 63 |
|
|
|
| |
|
|
|
| 25 |
|
|
| 67 | 59 |
|
| 4 |
| |
|
| 93 |
| |
3. | Set the Console Base (9) on the Left and Right Uprights | 3 |
|
|
| (1, 44). |
|
| |
|
|
|
| |
| While one person carefully feeds any slack Wire Harness |
| 75 | 62 |
| (25) down into the Right Upright (44), a second person |
|
| 75 |
| should carefully pull the slack Wire Harness from the |
|
| |
|
|
|
| |
| lower end of the Right Upright. | 1 |
|
|
|
|
|
| |
| Attach the Console Base (9) with four Screws (75). | 75 |
| 9 |
|
|
|
| |
| Align the holes in the Book Rack (62) with those in the |
| 25 |
|
| Console Base (9). Attach the Book Rack to the Console |
|
| |
| 44 |
|
| |
| Base with four Screws (75) as shown. |
|
| |
|
|
|
| |
|
|
|
| 75 |
5