ProForm 765 user manual Screws before tightening any of them

Page 10

10.Set the Pulse Bar Bottom (95) on the Left Handrail (35) and the Right Handrail (33). Press the Pulse Bar Bottom forward as you tighten two #10 x 3/4" Screws (5) with two #10 Star Washers (10) into the Handrails.

Remove the long tie from the Upright Wire (38).

11.With the help of a second person, hold the con- sole assembly near the Right Handrail (33) and the Left Handrail (not shown).

Connect the Upright Wire (38) to the Console Wire. See the inset drawing. The connectors should slide together easily and snap into place. If they do not, turn one connector and try again. IF THE CONNECTORS ARE NOT CON-

NECTED PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN YOU TURN ON THE POWER. Insert the connectors and the excess wire into the Right Handrail (33).

12.Connect the console ground wire to the handrail ground wire.

Set the console assembly on the Right Handrail (33) and Left Handrail (35). Make sure that the wire harnesses are not pinched. Attach the console assembly with two #8 x 1/2" Screws (1), four #8 x 3/4" Screws (12), and four #8 x 1/2" Washer Head Screws (112). Start all the

Screws before tightening any of them.

Cut the plastic tie from the Right Handrail (33).

See steps 4 and 6. Firmly tighten the four 3/8" x 4 1/2" Bolts (6).

10
		35
		10	Long Tie
		5	Long Tie
			5	38
				38
		95	10
			33
11
		Console	Console
		Wire	Assembly
	33	38
	33		Console
			Console
			Wire
			38
12		Console
		Console
		Assembly
				35

Ground Wires

	Plastic		12
112	Tie		112
	12	1
33	12

10

Image 10

Contents Model No. PFTL79507.0 Serial No QUESTIONS?Call TOLL-FREE Table of Contents Important Precautions Page Before YOU Begin Assembly Hardware may be included Tighten the Nut the Wheel must turn freely Make sure that the power cord is unplugged Do not fully fold the Frame yet See the inset drawing. Tie the long tieBe careful not to pinch the Upright Wire Not fully tighten the Bolts yetFirmly tighten the Bolts Screws before tightening any of them Pull on the sleeve to make sure that it is locked into place HOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Console Diagram Features of the ConsoleSelect the manual mode HOW to Turn on the PowerHOW to USE the Manual Mode Insert the key into the consoleChange the incline of the treadmill as desired Measure your heart rate if desired Turn on the fan if desiredSelect a cross training workout HOW to USE a Cross Training WorkoutPress the Quick Start button to start the work- out Continue the cross trainer workout HOW to USE a Classic Aerobic Workout Select a classic aerobic workoutStart the workout Select the monthly challengeGet a monthly challenge goal Complete the workout. See steps 4-9 onHOW to Review Your Monthly Challenge LOG Information ModeHOW to Adjust the Cushioning System Optional Chest Pulse SensorHOW to Fold the Treadmill for Storage HOW to Fold and Move the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useProblem The walking belt slows when walked on Page Workout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencySuggested Stretches R1207A Key No. Qty DescriptionQty Exploded Drawing A-Model No. PFTL79507.0 R1207A Exploded Drawing B-Model No. PFTL79507.0 R1207A Exploded Drawing C-Model No. PFTL79507.0 R1207A Exploded Drawing D-Model No. PFTL79507.0 R1207A Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT