ProForm 765 Make sure that the power cord is unplugged, Do not fully fold the Frame yet

Page 7

1. Make sure that the power cord is unplugged.

1

 

 

 

 

 

 

 

With the help of a second person, carefully tip

 

 

 

 

the treadmill onto its left side. Partially fold the

 

 

 

 

Frame (56) so that the treadmill is more stable;

 

 

38

Hole

do not fully fold the Frame yet.

 

 

83

Cut the tie securing the Upright Wire (38) to the

 

Tie

81

Base (83). Locate the tie in the indicated hole in

 

 

 

 

the Base, and use the tie to pull the Upright Wire

 

 

 

 

out of the hole.

 

 

 

2

Attach a Base Pad (81) to the Base (83) in the

 

 

 

 

location shown with a Base Pad Spacer (13) and

 

 

 

 

a #8 x 1" Tek Screw (2). Then, attach another

 

13

 

 

Base Pad (81) with only a #8 x 1" Tek Screw (2).

56

81

 

 

 

 

2

 

2. Attach a Wheel (84) with a 3/8" x 2" Shoulder

2

 

 

 

Bolt (111) and a 3/8" Nut (8). Do not over-

 

 

 

 

 

 

 

tighten the Nut; the Wheel must turn freely.

 

 

 

 

 

 

 

83

 

 

 

111

 

 

 

 

8

84

 

 

 

 

 

3. Identify the Right Upright (78) and the Right

3

 

 

 

Upright Spacer (79), which are marked with

 

 

 

38

 

 

 

stickers. Insert the Upright Wire (38) through the

 

 

 

 

 

 

 

Right Upright Spacer as shown.

 

 

 

78

See the inset drawing. Tie the long tie in the

 

Long Tie

38

Right Upright (78) securely around the end of

 

 

 

 

79

the Upright Wire (38). With the help of a second

 

 

 

 

 

 

83

person, hold the Right Upright near the Base

 

 

 

(83). Then, pull the other end of the long tie until

 

 

 

 

the Upright Wire is routed completely through

 

 

 

 

the Right Upright.

 

 

 

 

 

 

78

 

 

 

38

Wire

 

 

 

 

 

 

 

 

Tie

 

 

 

7

 

 

 

Image 7
Contents Model No. PFTL79507.0 Serial No QUESTIONS?Call TOLL-FREE Table of Contents Important Precautions Page Before YOU Begin Hardware may be included AssemblySee the inset drawing. Tie the long tie Make sure that the power cord is unpluggedDo not fully fold the Frame yet Tighten the Nut the Wheel must turn freelyNot fully tighten the Bolts yet Be careful not to pinch the Upright WireFirmly tighten the Bolts Screws before tightening any of them Pull on the sleeve to make sure that it is locked into place HOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Features of the Console Console DiagramInsert the key into the console HOW to Turn on the PowerHOW to USE the Manual Mode Select the manual modeChange the incline of the treadmill as desired Turn on the fan if desired Measure your heart rate if desiredSelect a cross training workout HOW to USE a Cross Training WorkoutPress the Quick Start button to start the work- out Continue the cross trainer workout Select a classic aerobic workout HOW to USE a Classic Aerobic WorkoutComplete the workout. See steps 4-9 on Select the monthly challengeGet a monthly challenge goal Start the workoutInformation Mode HOW to Review Your Monthly Challenge LOGOptional Chest Pulse Sensor HOW to Adjust the Cushioning SystemHOW to Fold the Treadmill for Storage HOW to Fold and Move the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingProblem The walking belt slows when walked on Page Exercise Frequency Exercise GuidelinesExercise Intensity Workout GuidelinesSuggested Stretches Key No. Qty Description R1207AQty Exploded Drawing A-Model No. PFTL79507.0 R1207A Exploded Drawing B-Model No. PFTL79507.0 R1207A Exploded Drawing C-Model No. PFTL79507.0 R1207A Exploded Drawing D-Model No. PFTL79507.0 R1207A Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT