ProForm 765 user manual Firmly tighten the Bolts

Page 9

7. Press a Front Handrail Endcap (97) into the Left

7

 

 

 

Handrail (35). Attach the Front Handrail Endcap

 

 

 

 

 

 

 

with a #8 x 3/4" Handrail Screw (15).

 

 

 

 

Press an Upright Insert (110) into the Left

 

 

 

97

 

 

 

 

Upright (74). Set the Left Handrail (35) on the

 

 

 

 

Upright Insert.

 

 

15

 

 

 

 

 

Attach the Left Handrail (35) with two 3/8" x 1

 

 

 

 

1/4" Bolts (7) and two 3/8" Star Washers (9).

 

 

 

 

Firmly tighten the Bolts.

 

35

 

 

 

 

 

110

 

 

 

 

9

 

 

 

 

7

 

 

 

74

 

 

8. Hold the Right Handrail (33) near the Right

8

 

 

 

Upright (78). Insert the Upright Wire (38)

 

 

 

 

 

 

97

through an Upright Insert (110), into the hole in

 

15

 

the bottom of the Right Handrail (33), and out of

 

Large Hole

 

 

the large hole in the side of the Right Handrail.

 

38

 

 

Insert the included plastic tie through the holes

 

 

 

 

in the Right Handrail (33) as shown. Look inside

 

Plastic Tie

 

 

the Right Handrail. Make sure that the plastic

7

 

 

 

 

 

tie holds the Upright Wire (38) to the side as

 

9

 

 

shown in the inset drawing. Tighten the plas-

 

 

Hole

 

tic tie.

 

 

Tie

 

110

33

 

 

Press a Front Handrail Endcap (97) into the

 

 

 

38

Right Handrail (33). Attach the Front Handrail

 

 

 

 

33

 

 

Endcap with a #8 x 3/4" Handrail Screw (15).

 

 

 

 

78

 

 

Attach the Right Handrail (33) with two 3/8" x

 

 

 

110

1 1/4" Bolts (7) and two 3/8" Star Washers (9).

 

 

Hole

 

Firmly tighten the Bolts.

 

 

 

 

9. Set the Console Base (93) face down on a soft

9

 

 

 

surface to avoid scratching the Console.

 

 

 

 

 

 

 

Remove the two indicated screws (A) from the

 

 

 

 

Pulse Bar Bottom (95). Discard the screws.

 

A

 

 

 

95

 

 

 

 

 

 

93

 

 

9

 

 

 

Image 9
Contents QUESTIONS? Model No. PFTL79507.0 Serial NoCall TOLL-FREE Table of Contents Important Precautions Page Before YOU Begin Hardware may be included AssemblyDo not fully fold the Frame yet Make sure that the power cord is unpluggedTighten the Nut the Wheel must turn freely See the inset drawing. Tie the long tieNot fully tighten the Bolts yet Be careful not to pinch the Upright WireFirmly tighten the Bolts Screws before tightening any of them Pull on the sleeve to make sure that it is locked into place Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Features of the Console Console DiagramHOW to USE the Manual Mode HOW to Turn on the PowerSelect the manual mode Insert the key into the consoleChange the incline of the treadmill as desired Turn on the fan if desired Measure your heart rate if desiredHOW to USE a Cross Training Workout Select a cross training workoutPress the Quick Start button to start the work- out Continue the cross trainer workout Select a classic aerobic workout HOW to USE a Classic Aerobic WorkoutGet a monthly challenge goal Select the monthly challengeStart the workout Complete the workout. See steps 4-9 onInformation Mode HOW to Review Your Monthly Challenge LOGOptional Chest Pulse Sensor HOW to Adjust the Cushioning SystemHOW to Fold and Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Move the Treadmill HOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingProblem The walking belt slows when walked on Page Exercise Intensity Exercise GuidelinesWorkout Guidelines Exercise FrequencySuggested Stretches Key No. Qty Description R1207AQty Exploded Drawing A-Model No. PFTL79507.0 R1207A Exploded Drawing B-Model No. PFTL79507.0 R1207A Exploded Drawing C-Model No. PFTL79507.0 R1207A Exploded Drawing D-Model No. PFTL79507.0 R1207A Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT