JVC RX7030VBK manual Dvd Tv/Dbs

English

Operating Video Components

IMPORTANT:

To operate JVC’s video components using the supplied remote control:

•You need to connect JVC’s video components through the AV COMPU LINK jacks (see page 42) in addition to the connections using cables with RCA pin plugs (see pages 14 and 15).

•Some JVC’s VCRs can accept two types of the control signals— remote code “A” and “B.” Before using this remote control, make sure that the remote control code of the target VCR is set to code “A.”

–For RX-8030VBK:When another JVC’s VCR is connected to the VCR 2 or VIDEO terminals, set its remote control code to code “B.” (This remote control cannot emit the control signals of code “B.”)

•When using the remote control, aim the remote control directly at the remote sensor on each component, not on the receiver.

VCR

You can always perform the following operations:

VCR 1 (for RX-8030VBK) or VCR (for RX-7030VBK): Turn on or off a VCR.

For RX-8030VBK:After pressing VCR 1 (or selecting “ VCR 1” by pressing CONTROL repeatedly), you can perform the following operations on a VCR:

For RX-7030VBK:After pressing VCR (or VCR CONTROL), you can perform the following operations on a VCR:

1 – 9, 0:	Select the TV channels on a VCR.
3:	Start playing.
REW:	Rewind a tape.

FF:Fast wind a tape.

7:	Stop playing or recording.
8:	Pause playing. To resume, press 3.
REC PAUSE:	Enter recording pause by pressing this button.
	To start recording again, press this button then 3.
CH +/–:	Change the TV channels on the VCR.

For RX-8030VBK:			RX-8030V
• When you press one of the source selection				ONLY
buttons, the operation mode appears on the
display window.
	Buttons	Indications
	VCR 1	VCR 1
	DVD or DVD MULTI	DVD
	TV/DBS	TV
	CONTROL (repeatedly)*	VCR 1	TAPE
		CDDSC	CDR

*By pressing CONTROL repeatedly, you can select

“VCR 1,” “TAPE,” “CDR” or “CDDSC” as the source.

When you press one of the buttons listed above, the remote operation mode appears on the operation mode display for about two hours.

Note:

You can use either VCR 1 (for RX-8030VBK) or VCR (for RX- 7030VBK) or the control button (CONTROL for RX-8030VBK or VCR CONTROL for RX-7030VBK) to activate the buttons listed above. If you press one of the source selection buttons, the playing source also changes. On the other hand, pressing the control button does not change the playing source.

DVD player

After pressing DVD or DVD MULTI, you can perform the following operations on a DVD player:

3: Start playing.

4: Return to the beginning of the current (or previous) chapter.

¢: Skip to the beginning of the next chapter.

7: Stop playing.

8: Pause playing. To resume, press 3.

After pressing DVD or DVD MULTI, these buttons can be used for the DVD menu operations.

4

Note:

For detailed menu operations, refer to the instructions supplied with the discs or the

DVD player.

2 3

MENU

56

ENTER

8

TV

You can always perform the following operations:

TV : Turn on or off the TV.

TV VOL +/–: Adjust the volume.

TV/VIDEO: Set the input mode (either TV or VIDEO).

After pressing TV/DBS, you can perform the following operations on a TV:

CH +/–:Change the channels.

1 – 9, 0, 100+: Select the channels.

RETURN: Alternate between the previously selected channel and the current channel.

46