ProForm 445i, PFTL413040 user manual Troubleshooting, Problem The power turns off during use, Top

Page 23

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please call our Customer Service Department toll- free at 1-888-533-1333, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays).

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 10). Use only a single-outlet surge suppres- sor that meets all of the specifications described on page 10. Important: The treadmill is not com- patible with GFCI-equipped outlets.

b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.

c. Check the reset/off circuit breaker located on the

c

 

treadmill near the power cord. If the switch protrudes

 

 

 

as shown, the circuit breaker has tripped. To reset

Tripped

Reset

the circuit breaker, wait for five minutes and then

 

 

press the switch back in.

 

 

PROBLEM: The power turns off during use

SOLUTION: a. Check the reset/off circuit breaker located on the treadmill frame near the power cord (see c. above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c. Remove the key from the console. Reinsert the key into the console.

d. If the treadmill still will not run, please call our Customer Service Department, toll-free.

PROBLEM: The speed display on the console does not function properly

SOLUTION: a. Remove the key and UNPLUG THE POWER CORD. Remove the Hood Screws (58) and the Hood (94) from the treadmill.

Locate the Reed Switch (21) and the Magnet (43) on the left side of the Pulley (42). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is about 1/8”. If necessary, loosen the Screw (62), move the Reed Switch slightly, and then retighten the Screw. Reattach the hood, and run the treadmill for a few minutes to check for a correct speed reading.

 

58

58

94

 

 

58

1/8”

42

62

 

21

43

Top

 

View

 

23

Image 23 Contents
Customer HOT Line QUESTIONS?Model No. PFTL413040 Serial No Table of Contents Important Precautions Page Back Right Side Before YOU BeginMake sure that the power cord is not plugged AssemblyAble to turn freely Careful not to pinch the wires. Insert two 2 3/4 BoltsRight side. Be careful not to damage the Upright Wire Do not overtighten the Wheel Bolt the Wheel must beRack Bolts and Nuts before tightening any of them Top View Performant Lubetm Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Features of the Console Console DiagramHOW to USE the Manual Mode HOW to Turn on the PowerWhenkey. you are finished exercising, remove Measure your heart rate, if desiredTurn on the fan if desired Select a speed program HOW to USE a Speed ProgramWhen the program is completed, remove Key from the console Insert the key fully into the consoleHOW to Connect Your Portable Stereo HOW to Connect Your Computer HOW to Connect Your Home StereoAdapter Audio Cable HOW to Connect Your VCRWhenkey. the program is completed, remove PressVCR. the Play button on your CD player orReturn to the treadmill and stand on the foot HOW to USE Programs Directly from OUR WEB SiteFollow the on-line instructions to start Program Information Mode HOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USE Top TroubleshootingProblem The power turns off during use Problem The walking belt slows when walked on Exercise Frequency Conditioning GuidelinesExercise Intensity Workout GuidelinesSuggested Stretches Page Key Qty Description R1004BModelNo. PFTL413040 Exploded DRAWING-Model No. PFTL413040 Part 2 R1004B Exploded DRAWING-Model No. PFTL413040 Part 3 R1004B Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT HOW to Order Replacement PartsLimited Warranty