ProForm 445i Careful not to pinch the wires. Insert two 2 3/4 Bolts, Able to turn freely

Page 7

2. Identify the Right Upright (10). Note: The Left Upright (9)

has the Latch Housing (77, see step 3) attached to it.

Have a second person hold the Right Upright (10) near the

Base (82) as shown. Orient the Right Upright so that it is

angled forward (see step 3). Feed the Upright Wire

Harness (17) into the lower end of the Right Upright and

out of the upper end.

Next, hold the Right Upright (10) against the Base (82). Be

careful not to pinch the wires. Insert two 2 3/4” Bolts

(47), with two Washers (29) and two Star Washers (81),

into the Base, and loosely thread the Bolts into the lower

end of the Right Upright (10).

Attach a Wheel (95) to the Base (82) with a Wheel Bolt (86).

Do not overtighten the Wheel Bolt; the Wheel must be

able to turn freely.

With the help of a second person, tip the treadmill onto its

right side. Be careful not to damage the Upright Wire

Harness (17). Have a second person hold the Left Upright

(9) near the Base (82). Orient the Left Upright so that it is

angled forward (see step 3). Attach the Left Upright and

the other Wheel (not shown) as described above. Note:

There are no wires in the Left Upright.

3. With the help of a second person, set the treadmill on the

floor with the Left and Right Uprights (9, 10) vertical.

Identify the Right Handrail (124), which has a large hole

in the left side. Feed the Wire Harness (17) up through

the hole in the bottom of the Right Handrail and out of

the large hole in the left side. Note: It may be helpful to

use needlenose pliers to pull the Wire Harness out of the

2

 

 

 

 

10

 

17

 

 

 

86

47

81

 

29

95

 

 

 

 

9

 

82

 

 

81

 

47

 

 

 

29

 

3

56

 

 

 

 

 

17

123

56

large hole.

Set the Right Handrail (124) on the Right Upright (10).

9

77

Large

Hole

Finger tighten a 4” Bolt (120) through the Right Upright into

the lower end of the Right Handrail. Attach the upper end

of the Right Handrail with a 2 1/2” Bolt (56). Do not

tighten the Bolts yet.

Attach the Left Handrail (123) as described above. Note:

There is not a wire in the Left Handrail.

124

120

10

120

7

Image 7 Contents
Model No. PFTL413040 Serial No QUESTIONS?Customer HOT Line Table of Contents Important Precautions Page Back Right Side Before YOU BeginMake sure that the power cord is not plugged AssemblyAble to turn freely Careful not to pinch the wires. Insert two 2 3/4 BoltsRight side. Be careful not to damage the Upright Wire Do not overtighten the Wheel Bolt the Wheel must beRack Bolts and Nuts before tightening any of them Top View HOW to Plug in the Power Cord Operation and AdjustmentPerformant Lubetm Walking Belt Features of the Console Console DiagramHOW to USE the Manual Mode HOW to Turn on the PowerTurn on the fan if desired Measure your heart rate, if desiredWhenkey. you are finished exercising, remove Select a speed program HOW to USE a Speed ProgramWhen the program is completed, remove Key from the console Insert the key fully into the consoleHOW to Connect Your Portable Stereo HOW to Connect Your Computer HOW to Connect Your Home StereoAdapter Audio Cable HOW to Connect Your VCRWhenkey. the program is completed, remove PressVCR. the Play button on your CD player orFollow the on-line instructions to start Program HOW to USE Programs Directly from OUR WEB SiteReturn to the treadmill and stand on the foot Information Mode HOW to Fold the Treadmill for Storage HOW to Fold and Move the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingTop Problem The walking belt slows when walked on Exercise Frequency Conditioning GuidelinesExercise Intensity Workout GuidelinesSuggested Stretches Page Key Qty Description R1004BModelNo. PFTL413040 Exploded DRAWING-Model No. PFTL413040 Part 2 R1004B Exploded DRAWING-Model No. PFTL413040 Part 3 R1004B Limited Warranty HOW to Order Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT