ProForm PFT39110.0 user manual See the far right drawing. Tie the wire tie, Tighten the Bolt yet

Page 8

4. Raise the Uprights (77, 78), and position the

4

74

 

 

 

Base (85) near the treadmill as shown.

78

 

 

See the far right drawing. Tie the wire tie in the

 

Wire Tie

 

 

lower end of the Right Upright (78) around the

 

77

 

 

 

Upright Wire (74). Then, pull the other end of the

 

 

74

 

wire tie until the Upright Wire is routed through

 

 

 

 

the Right Upright.

 

 

Large

 

 

Make sure that the end of the Upright Wire

 

 

 

 

 

 

Hole

 

 

(74) does not fall into the Right Upright (78).

 

 

 

Wire

 

 

 

 

 

 

 

 

85

Tie

 

 

 

 

 

5. See the left inset drawing. Identify the two

5

 

 

 

 

Frame Spacers (79). Open the included packet

 

 

 

 

of grease, and apply grease to both sides of

 

 

 

78

 

both Frame Spacers. Then, identify the outer

 

 

 

 

side of each Frame Spacer.

 

 

13

 

 

Hold a Frame Spacer (79) between the Right

 

 

 

 

Upright (78) and the Lift Frame (65), with the

 

 

 

79

 

outer side of the Frame Spacer facing the

 

 

 

 

Right Upright. Attach the Right Upright to the

 

 

 

 

 

Lift Frame with a 3/8" x 2 1/2" Bolt (1), a 3/8"

 

 

 

10

 

Washer (10), and a 3/8" Nut (13); do not

 

 

 

1

tighten the Bolt yet.

 

65

 

 

 

 

 

 

 

 

 

Grease

13

78

 

 

 

 

 

 

 

 

79

79

10

1

 

 

 

 

 

 

 

Outer Side

65

 

 

 

 

 

 

 

 

8

 

 

 

 

Image 8
Contents QUESTIONS? Model No. PFTL39110.0 Serial NoMon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MT On the WEBTable of Contents Important Precautions Treadmill, and before performing the main Before YOU Begin Assembly Page See the far right drawing. Tie the wire tie Make sure that the end of the Upright WireDoes not fall into the Right Upright See the left inset drawing. Identify the twoPage Start all four Bolts, and then firmly tighten Each of them Careful not to pinch any wiresBracket 70. Orient the Pulse Assembly so Nectors PROPERLY, the Console MAY Become Damaged When YOU Turn on PowerIf YOU do not Connect the CON 2 Bolts Side View View from Above PRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Console Diagram Features of the ConsoleHOW to Turn on the Power HOW to USE the Manual ModeInsert the key into the console Start the walking beltMeasure your heart rate if desired. Before using HOW to USE a Preset Application Information Mode HOW to Fold and Move the Treadmill HOW to Fold the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USECompatible with GFCI-equipped outlets TroubleshootingProblem The power turns off during use View Problem The walking belt slows when walked on Key and Unplug the Power CORD. UsingTop Walking belt has shifted to the right, turn the leftExercise Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencyPart LIST-Model No. PFTL39110.0 Key No. Qty DescriptionExploded Drawing R0610A Exploded Drawing C-Model No. PFTL39110.0 Exploded Drawing D-Model No. PFTL39110.0 Icon Health & Fitness, Inc., 1500 S W., Logan, UT Ordering Replacement PartsLimited Warranty