ProForm PFTL13011.0 user manual Assembly, Start all four Screws, and then tighten them

Page 11

9.

Remove and discard the #10 x 3/4" Screws

9

 

 

(3) from the Right Handrail (93) and the Left

93

 

 

 

Handrail (not shown).

 

 

 

Pulse Wire

 

 

 

 

Hold the pulse assembly near the Right Handrail

 

3

 

(93). Insert the pulse wire from the pulse assem-

 

 

 

bly into the hole in the side of the Right Handrail

 

Pulse

 

and pull it out of the end of the Right Handrail as

 

Assembly

 

shown.

 

 

 

 

 

Hole

10.

Slide the pulse assembly onto the Left and Right

10

 

 

Handrails (92, 93). Make sure that the brack-

93

 

 

ets on the pulse assembly are flush against

 

Pulse Wire

3

the rubber on the Handrails. Be careful not

 

 

 

 

11

to pinch the pulse wire against the pulse

 

Pulse

assembly.

 

 

Attach the pulse assembly with four #10 x 3/4"

92

Assembly

 

11 3

 

Screws (3) and four #10 Star Washers (11).

 

 

Start all four Screws, and then tighten them.

 

 

 

11. Set the console assembly face down on a soft

11

 

1

surface to avoid scratching the console

 

assembly.

 

1

1

Identify the Left and Right Trays (110, 111).

 

 

110

111

 

 

 

Attach the Trays (110, 111) to the console

4

1

4

assembly with six #8 x 1/2" Screws (1). Start all

 

12

six Screws, and then tighten them. Be care-

12

 

ful not to overtighten the Screws.

 

 

 

Remove the four 5/16" x 5/8" Screws (4) and

 

 

 

5/16" Star Washers (12) from the console

 

 

 

assembly. They will be used in step 13.

 

 

 

 

 

 

Console

 

 

 

Assembly

 

11

 

 

Image 11
Contents Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MT QUESTIONS?Model No. PFTL13011.0 Serial No Call TOLL-FREETable of Contents Important Precautions Page Before YOU Begin Part Identification Chart Make sure that the power cord is unplugged AssemblySee the inset drawing. Tie the wire tie Base Covers into place yet Be careful not to pinch the wires. IfFully tighten the Screws yet. Note It may be Attach the Right Upright not shownScrews and Star Washers will be used Step Start all four Screws, and then tighten them AssemblyAssembly. They will be used in step Screws, and then tighten them Is shown. Start all four Screws, and then Tighten them Page Chest Heart Rate Monitor HOW to PUT on the Heart Rate MonitorCare and Maintenance TroubleshootingUse a Surge Suppressor Operation and AdjustmentHOW to Connect the Power Cord Console Diagram Features of the Console Insert the key into the console HOW to Turn on the PowerHOW to USE the Manual Mode Select the manual modeFollow your progress with the displays Change the incline of the treadmill as desiredTurn on the fan if desired Measure your heart rate if desiredStart the workout HOW to USE AN Onboard WorkoutSelect an onboard workout Start the workout. See on HOW to USE AN Ifit Live WorkoutInsert the iFit Live module into the console Select an iFit Live workoutHOW to USE the Stereo Sound System COOL-DOWN ModeMetric Information ModeHOW to Lower the Treadmill for USE HOW to Fold and Move the TreadmillHOW to Fold the Treadmill HOW to Move the TreadmillSymptom The power turns off during use TroubleshootingSymptom The power does not turn on Symptom The walking belt slows when walked on Page Exercise Frequency Exercise GuidelinesExercise Intensity Workout GuidelinesQty Description Part ListDescription Qty Drawing a Exploded Drawing B Exploded Drawing C Exploded Drawing D Icon Health & Fitness, Inc., 1500 S W., Logan, UT Ordering Replacement PartsLimited Warranty
Related manuals
Manual 36 pages 30.55 Kb