ProForm 325i, PFTL31330 user manual Troubleshooting, Solution, Power Cord

Page 15

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please call our Customer Service Department toll-

free at 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays).

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 10). Use only a single-outlet surge suppres- sor that meets all of the specifications described on page 10. Important: The treadmill is not com- patible with GFCI-equipped outlets.

b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.

c.Check the reset/off circuit breaker located on the treadmill frame near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch back in.

PROBLEM: The power turns off during use

c

Tripped

Reset

SOLUTION: a. Check the reset/off circuit breaker located on the treadmill frame near the power cord (see the drawing above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b.Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c.Remove the key from the console. Reinsert the key fully into the console.

d.If the treadmill still will not run, please call our Customer Service Department toll-free.

PROBLEM: The displays of the console do not function properly

SOLUTION:

a. Remove the key from the console and

UNPLUG THE

 

POWER CORD.

Remove the six 3/4” Screws (2) from

 

the Hood (1), and carefully pivot the Hood off.

Locate the Reed Switch (10) and the Magnet (18) on

 

the left side of the Pulley (17). Turn the Pulley until

 

the Magnet is aligned with the Reed Switch.

Make

sure that the gap between the Magnet and the

 

 

Reed Switch is about 1/8”.

If necessary, loosen the

Screw (26) and move the Reed Switch slightly. Retighten the Screw. Re-attach the Hood, and run the treadmill for a few minutes to check for a correct speed reading.

a

2

2

 

2

1

 

1/8”

17

10

 

26

18

Top

 

View

 

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents
Customer HOT Line To Avoid DELAYS, Please Call Direct to OUR TollQUESTIONS? Model No. PFTL31330 Serial NoTable of Contents Never leave the treadmill unattended while it Important PrecautionsUse the treadmill only as described Same circuit. Do not use an extension cordPage Using the treadmill Before YOU BeginBack Tighten the Nut AssemblyAdjustable wrench Wire cutters Until instructed to do soOpen part bag C Careful not to damage the Wire HarnessTouch Side of the Right HandrailEnds of the plastic ties Firmly tighten the 1 Bolts 63 Make sureHandrails. Firmly tighten the 3 Bolts Grounded Outlet Box HOW to Plug in the Power CordPerformant Lube This product must be grounded.If it should malfuncSTEP-BY-STEP Console Operation Console Diagram HOW to USE the Hand Weights HOW to Move the Treadmill HOW to Fold the Treadmill for StorageFrame HOW to Lower the Treadmill for USETroubleshooting SolutionPower Cord Belt has shifted to the left Problem The walking belt slows when walked onUnplug the Power Cord Come damaged. Remove the keyExercise Frequency Conditioning GuidelinesExercise Intensity Workout GuidelinesSuggested Stretches Page Red Wire, 2F Key No. Qty DescriptionWasher Belly Pan R0903B Part No R0903B Ordering Replacement PartsLimited Warranty Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT
Top Page Image Contents