ProForm PFTL31330 Problem The walking belt slows when walked on, Come damaged. Remove the key

Page 16

PROBLEM: The walking belt slows when walked on

SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 10.

b.If the walking belt is overtightened, treadmill perfor- mance may decrease and the walking belt may be-

come damaged. Remove the key and

UNPLUG THE

POWER CORD

. Using the allen wrench, turn both

rear roller adjustment bolts counterclockwise, 1/4 of a turn. When the walking belt is properly tightened, you should be able to lift each side of the walking belt 2 to 3 inches off the walking platform. Be careful to keep the walking belt centered. Plug in the power cord, in- sert the key, and run the treadmill for a few minutes. Repeat until the walking belt is properly tightened.

b

2”–3”

Rear Roller Adjustment Bolts

c. If the walking belt still slows when walked on, call our Customer Service Department toll-free.

PROBLEM: The walking belt is off-center or slips when walked on

 

 

SOLUTION:

a. If the walking belt is off-center, first remove the key

 

and UNPLUG THE POWER CORD

. If the walking

 

belt has shifted to the left,

use the allen wrench to

 

turn the left rear roller bolt clockwise 1/2 of a turn;

if

 

the walking belt has shifted to the right,

 

turn the

 

bolt counterclockwise 1/2 of a turn. Be careful not to

 

 

overtighten the walking belt. Plug in the power cord,

 

 

insert the key, and run the treadmill for a few minutes.

 

 

Repeat until the walking belt is centered.

 

 

b. If the walking belt slips when walked on, first remove

 

 

the key and

UNPLUG THE POWER CORD

. Using

 

the allen wrench, turn both rear roller bolts clockwise,

 

 

1/4 of a turn. When the walking belt is correctly tight-

 

ened, you should be able to lift each side of the walk-

 

ing belt 2 to 3 inches off the walking platform. Be

 

 

careful to keep the walking belt centered. Plug in the

 

 

power cord, insert the key, and carefully walk on the

 

 

treadmill for a few minutes. Repeat until the walking

 

 

belt is properly tightened.

 

 

a

b

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents To Avoid DELAYS, Please Call Direct to OUR Toll QUESTIONS?Model No. PFTL31330 Serial No Customer HOT LineTable of Contents Important Precautions Use the treadmill only as describedSame circuit. Do not use an extension cord Never leave the treadmill unattended while itPage Before YOU Begin Using the treadmillBack Assembly Adjustable wrench Wire cuttersUntil instructed to do so Tighten the NutCareful not to damage the Wire Harness Open part bag CSide of the Right Handrail TouchEnds of the plastic ties Make sure Firmly tighten the 1 Bolts 63Handrails. Firmly tighten the 3 Bolts HOW to Plug in the Power Cord Performant LubeThis product must be grounded.If it should malfunc Grounded Outlet BoxConsole Diagram STEP-BY-STEP Console OperationHOW to USE the Hand Weights HOW to Fold the Treadmill for Storage HOW to Move the TreadmillHOW to Lower the Treadmill for USE FrameSolution TroubleshootingPower Cord Problem The walking belt slows when walked on Unplug the Power CordCome damaged. Remove the key Belt has shifted to the leftConditioning Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencySuggested Stretches Page Key No. Qty Description Red Wire, 2FWasher Belly Pan R0903B Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT Part No R0903B
Top Page Image Contents