JVC FS-A52 manual Connecting Speakers, To connect speakers, To remove the speaker grilles

Page 11

Continued

Connecting Speakers

To connect speakers

You can connect the speakers by following the procedure

	below:
	1
	2	Speaker terminals		3,4
		SPEAKER IMPEDANCE
			MIN 4Ω
	Speaker cord	+	+	Speaker cord
	Speaker cord	R	L	Speaker cord
		R	L
		–	–
		R		L
	Rear of the right		Rear of the left
	speaker		speaker

1If cords are covered with insulation, twist the core of the cord at the end of each cord, then remove the insulation.

2Open the speaker terminal.

3Insert the end of the speaker cord to the terminal. Match the polarity: White cord to (+) terminal and black cord to (–) terminal.

4Close the speaker terminal on the rear of the unit.

Use only speakers with the speaker impedance—4 Ω to16 Ω.

To remove the speaker grilles

The speaker grilles are removable.

Holes Projections

Speaker grille

To remove the speaker grille, insert your fingers at the top

of the speaker grille, then pull towards you. Do the same at the bottom.

To attach the speaker grille, put the projections of the

speaker grille into the holes of the speaker.

– 8 –

Image 11

Contents FS-A52- Consists of CA-FSA52 and SP-UXA52 Compact Component SystemClass 1 Laser Product Produit Laser Classe Mises en garde, précautions et indications diversesFor Canada/pour le Canada Introduction PrecautionsContents Front view Location of the ButtonsMain Unit Top viewMain unit Display-indicatorsRemote control Remote ControlUnpacking Putting the Batteries into the Remote ControlGetting Started To connect an outdoor AM antenna FM antennaAM antenna To connect an outdoor FM antennaTo attach the speaker grille, put the projections Connecting SpeakersTo connect speakers To remove the speaker grillesFor playing the other equipment through this unit Connecting Other EquipmentTo stop and cancel the display demonstration, press To connect analog audio equipmentMain unit Front view Basic and Common OperationsMain unit Top view Selecting the Sources and Starting Play Turning On the PowerSelecting the Sound Modes Adjusting the VolumeTurning On/Off the Key-touch Tone Reinforcing the Bass SoundTo select TODAY’S Color Setting the Display IlluminationTo adjust and register the color To select the color patternListening to FM and AM Broadcasts To change the FM reception mode Tuning in a StationPresetting Stations To check the clock time while listening to the broadcast Tuning in a Preset StationPlaying Back a CD CancelPlaying Back the Entire CD-Normal Play Precautions on CD PlaybackBasic CD Operations To modify the program To check the program contentsProgram Play To skip the current track, press ¢ Playing at Random-Random PlayRepeating Tracks-Repeat Play Display Playing Back a TapeTo check the clock time while playing back a tape To play both sides-Reverse ModePlaying Back a Tape Mode PRO Using External EquipmentPlay the CD Player of this unit Listening to External EquipmentRecording from This Unit to External Equipment Press AUX/MDFor recording operations, mainly use the buttons on the unit Recording on TapesTo demagnetize the head Before You Start RecordingTo protect your recordings To keep the best recording and playback sound qualityRecording CD-CD Synchronized Recording What’s a Recording Mode and Reverse Mode ?Recording FM/AM Broadcasts To record a single track during play or pause Recording External EquipmentUsing the Timers How Recording Timer actually works Setting the ClockUsing Recording Timer To turn off the Recording Timer after its setting is done Using Daily TimerHow Daily Timer actually works Press SET When you have selected from FM orMinute digit of timer-off time starts flashing on Timer-on time, then press SETHour digit of timer-off time starts flashing on Timer-off time, then press SETHow Sleep Timer actually works Using Sleep TimerTimer Priority Handling discs MaintenanceCleaning the unit General NotesOutput Power 40 W 20 W + 20 W at 4 Ω 10 % THD TroubleshootingAuthorized Service Centers Limited Warranty JVC 0102MWMMDWJEM