JVC FS-A52 Adjusting the Volume, Turning On/Off the Key-touch Tone, Reinforcing the Bass Sound

Page 15

Continued

Adjusting the Volume

You can adjust the volume level while the unit is turned on. The volume level has no effect on recording.

To increase the volume, press VOLUME +.

To decrease the volume, press VOLUME –.

(Maximum)

(Minimum)

The volume level meter appears on the display.

•The volume level can be adjusted in 41 steps (VOL MIN, VOL 1 – VOL 39, and VOL MAX.)

•When pressing and holding the button, you can change the volume level continuously.

For private listening

Connect the headphones to the PHONES jack. No sound comes out of the speakers. Be sure to turn down the volume before connecting or putting on the headphones.

DO NOT turn off (on standby) the unit with the volume set to an extremely high level; otherwise, the sudden blast of sound can damage your hearing, speakers and/or headphones when you turn on the unit or start playing any source.

REMEMBER you cannot adjust the volume level while the unit is on standby mode.

Turning On/Off the Key-touch Tone

If you do not want the key-touch tone to beep each time you press buttons, you can deactivate it while the unit is turned on.

On the remote control ONLY:

Press BEEP.

•Each time you press the button, the key-touch tone turns on (BEEP ON) and off (BEEP OFF) alternately:

BEEP ON BEEP OFF

Reinforcing the Bass Sound

The richness and fullness of the bass sound is clearly maintained regardless of how low you set the volume— Active Hyper Bass PRO. You can select the bass effect levels while the unit is turned on. The AHB PRO can be applied only to playback sounds, and cannot be used for recording.

To get the effect, press AHB PRO.

The AHB PRO indicator lights on the display.

•Each time you press the button, the effect changes as

follows:

AHB 1 AHB 2

AHB OFF

(Canceled)

AHB 1: Bass sound is clearly heard even in the low volume.

AHB 2: Bass sound is more effective than AHB 1.

AHB OFF: Cancels the AHB PRO.

The AHB PRO indicator goes off from the display.

To check the AHB PRO setting currently selected, press

AHB PRO once while the AHB PRO indicator is lit.

Selecting the Sound Modes

You can select one of the 4 preset sound modes while the unit is turned on. The sound modes can be applied only to playback sounds, and cannot be used for recording.

On the remote control ONLY:

To select the sound modes, press SOUND MODE repeatedly until the sound mode you want appears on the display.

The SOUND indicator also lights on the display.

•Each time you press the button, the sound mode changes as follows:

ROCK POP CLASSIC

FLAT JAZZ

(Canceled)

ROCK: Boosts low and high frequency. Good for acoustic music.

POP: Good for vocal music or voice.

CLASSIC: Good for classical music.

JAZZ: Good for jazz music.

FLAT: Cancels the sound mode.

The SOUND indicator goes off from the display.

To check the sound mode currently selected, press SOUND MODE once while the SOUND indicator is lit.

– 12 –

Page 14 Page 16
Image 15
Page 14 Page 16
Contents FS-A52- Consists of CA-FSA52 and SP-UXA52 Compact Component SystemClass 1 Laser Product Produit Laser Classe Mises en garde, précautions et indications diversesFor Canada/pour le Canada Introduction PrecautionsContents Front view Location of the ButtonsMain Unit Top viewMain unit Display-indicatorsRemote control Remote ControlPutting the Batteries into the Remote Control Getting StartedUnpacking To connect an outdoor AM antenna FM antennaAM antenna To connect an outdoor FM antennaTo attach the speaker grille, put the projections Connecting SpeakersTo connect speakers To remove the speaker grillesFor playing the other equipment through this unit Connecting Other EquipmentTo stop and cancel the display demonstration, press To connect analog audio equipmentBasic and Common Operations Main unit Top viewMain unit Front view Selecting the Sources and Starting Play Turning On the PowerSelecting the Sound Modes Adjusting the VolumeTurning On/Off the Key-touch Tone Reinforcing the Bass SoundTo select TODAY’S Color Setting the Display IlluminationTo adjust and register the color To select the color patternListening to FM and AM Broadcasts Tuning in a Station Presetting StationsTo change the FM reception mode To check the clock time while listening to the broadcast Tuning in a Preset StationPlaying Back a CD CancelPlaying Back the Entire CD-Normal Play Precautions on CD PlaybackBasic CD Operations To check the program contents Program PlayTo modify the program Playing at Random-Random Play Repeating Tracks-Repeat PlayTo skip the current track, press ¢ Display Playing Back a TapeTo play both sides-Reverse Mode Playing Back a TapeTo check the clock time while playing back a tape Mode PRO Using External EquipmentPlay the CD Player of this unit Listening to External EquipmentRecording from This Unit to External Equipment Press AUX/MDFor recording operations, mainly use the buttons on the unit Recording on TapesTo demagnetize the head Before You Start RecordingTo protect your recordings To keep the best recording and playback sound qualityWhat’s a Recording Mode and Reverse Mode ? Recording FM/AM BroadcastsRecording CD-CD Synchronized Recording To record a single track during play or pause Recording External EquipmentUsing the Timers Setting the Clock Using Recording TimerHow Recording Timer actually works To turn off the Recording Timer after its setting is done Using Daily TimerHow Daily Timer actually works Press SET When you have selected from FM orMinute digit of timer-off time starts flashing on Timer-on time, then press SETHour digit of timer-off time starts flashing on Timer-off time, then press SETUsing Sleep Timer Timer PriorityHow Sleep Timer actually works Handling discs MaintenanceCleaning the unit General NotesOutput Power 40 W 20 W + 20 W at 4 Ω 10 % THD TroubleshootingAuthorized Service Centers Limited Warranty JVC 0102MWMMDWJEM
Top Page Image Contents