ProForm PFBE66080 manual

Page 8

7.Attach the Seat (14) to the Seat Brackets (9, 46) with four M6 x 16mm Screws (3) and four M6 Washers (68).

Insert the Long ÒLÓ-Pin (71) through the holes in the Seat Brackets (9, 46) and the Frame (54).

8.Press a 2Ó Square Inner Cap (17) into each of the open ends of the Leg Lever (18).

Slide the Weight Tube (51) into the indicated hole in the Leg lever (18). Secure the Weight Tube with the M8 x 70mm Bolt (52), two Thin M8 Washers (22), a 1/2Ó Spacer (50) and an M8 Nylon Locknut (13).

Press a 1Ó Round Inner Cap (12) into the indicated end of the Weight Tube (51). Press the Angle Cap (49) onto the indicated end of the Weight Tube.

Press a Weight Adapter Bushing (47) into each end of a Short Weight Adapter (48). Slide the Weight Adapter onto the Weight Tube (51) and secure it with an M6 x 32mm Bolt (7) and an M6 Nylon Locknut (2).

Note: If you are not going to use olympic weights, you do not need to mount the Weight Adapter.

9.Attach the Lock (62) to the Pad Upright (19) with the M8 x 62mm Bolt (58), a Thin M8 Washer (22), a Lock Spacer (66) and an M8 Nylon Locknut (13). Do not overtighten the Nylon Locknut. You must be able to freely pivot the Lock.

Lubricate the M10 x 72mm Bolt (59). Attach the Leg Lever (18) to the bracket (C) on the Pad Upright (19) with the Bolt and an M10 Nylon Locknut (1). Do not overtighten the Nylon Locknut. You must be able to freely pivot the Leg Lever.

10.Press a 3/4Ó Round Inner Cap (65) into each end of the three Pad Tubes (67, 77).

Insert a Short Pad Tube (67) into the upper hole in the Leg Lever (18) as shown. Slide a Foam Pad onto each end of the Short Pad Tube.

Insert a Long Pad Tube (77) into the lower hole in the Leg Lever (18) as shown. Slide a Foam Pad onto each end of the Long Pad Tube.

Insert a Pad Tube (67) through one of the holes in the bracket (C) on the Pad Upright (19). Slide a 6Ó Foam Pad (10) onto each end of the Pad Tube.

8

7

 

 

 

 

14

 

 

 

 

 

 

 

 

 

 

 

 

9

 

54

 

46

68

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

71

 

3

68

 

 

 

 

 

 

 

 

 

 

 

 

3

 

 

8

17

 

 

 

 

 

 

18

 

 

 

 

49

 

 

 

17

 

 

 

 

 

 

 

 

22

 

52

 

7

 

 

 

22

 

 

 

 

 

 

 

47

48

47

 

 

 

 

 

 

50

17

51

 

 

 

 

13

 

 

 

 

 

 

 

 

2

12

 

 

 

 

 

 

 

 

9

 

C

1

 

 

 

 

 

 

 

 

 

 

 

 

13

 

 

 

59

 

 

 

 

18

 

58

 

66

62

 

 

 

 

 

 

 

 

 

22

 

 

 

 

 

 

 

19

 

 

 

 

10

 

 

65

 

10

 

 

 

 

 

 

 

 

 

 

19

 

67

 

 

 

 

65

 

 

 

 

 

 

 

77

 

 

 

 

 

 

 

 

 

 

 

C

 

 

65

 

 

 

 

 

 

 

 

 

 

 

67

 

 

 

 

 

65

 

 

 

 

 

10

 

 

 

10

 

 

 

 

 

 

 

18

 

 

 

 

 

Image 8
Contents Customer HOT Line Patent PendingModel No. PFBE66080 Serial No Table of Contents Important Precautions Assembled Dimensions Before You BeginPart Identification Chart Model No. PFBE66080 R0200A Assembly Locknut. You must be able to freely pivot the Decline StrutPage Page Page Do not tighten the Nylon Locknuts yet Not tighten the Nylon Locknut yetTop Frame fit into the Uprights Page Page Adjusting the Weight Bench Using the Barbell RacksAdjusting the Seat Incline Adjusting the BackrestAttaching Weights to the LEG Lever Locking the LEG LeverAttaching Weights to the Weight Carriages Securing Weights with the Spring ClipsExercise Guidelines Staying Motivated Muscle ChartCooling Down Exercise Weight Sets Reps DateAerobic Exercise Thursday Aerobic Exercise DatePart List Model No. PFBE66080 Qty DescriptionExploded Drawing Model No. PFBE66080 Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT Ordering Replacement PartsLimited Warranty