HOW TO ADJUST THE REED SWITCH
| 10 |
| 40 |
8 |
|
40 | 53 |
| |
| 7 |
If the console does not display correct feedback, the reed switch should be adjusted. In order to adjust the reed switch, the Left Side Shield (10) must be removed. Using an adjustable wrench, turn the Left Pedal (8) clockwise and remove it from the Crank (53). Remove the three M4 x 12mm Screws (40) and the two M4 x 16mm Screws (7) from the Left Side Shield. Make sure that the arm of the Crank is in the position shown in the drawing above. Carefully slide the Left Side Shield forward off the arm of the Crank and remove it.
4 |
53 |
7 |
49 |
Next, locate the Reed Switch (49). Turn the Crank
(53)until the Magnet (4) is aligned with the Reed Switch. Loosen but do not remove the M4 x 16mm Screw (7). Slide the Reed Switch slightly closer to or away from the Magnet. Retighten the Screw. Turn the Crank for a moment. Repeat until the console displays correct feedback. When the Reed Switch is correctly adjusted, reattach the left side shield and pedal.
HOW TO ADJUST THE RESISTANCE STRAP
If there is not enough pedaling resistance when the resistance knob is turned to the highest setting, the Resistance Strap (15) may need to be adjusted. To adjust the Resistance Strap, the left side shield must
first be removed. Refer to the instructions on page 7 and remove the left side shield.
Next, turn the |
|
| |
resistance knob to | 53 | 38 | |
the lowest setting. | |||
| |||
Locate and open |
|
| |
the Strap Clamp |
| 15 | |
(38). Grip the end |
|
| |
of the Resistance |
|
| |
Strap (15) and |
|
| |
pull it up slightly. |
|
| |
While holding the |
|
| |
end of the |
|
| |
Resistance Strap, |
|
|
fully close the Strap Clamp. Turn the Crank (53) for a moment to make sure that there is not too much resis- tance. When the Resistance Strap is properly adjust- ed, reattach the left side shield and pedal.
HOW TO ADJUST THE DRIVE BELT
The exercise |
|
cycle features a | 14 |
precision drive |
|
belt that must be |
|
kept properly |
|
adjusted. If the |
|
belt causes | Top View |
excessive noise |
|
or slips as you |
|
pedal, the belt |
|
should be |
|
checked. To do |
|
this, the side shields must first be removed. Refer to the instructions on page 7 and remove the left side shield. Next, remove the right side shield in the same way.
Press down on |
|
|
the center of the | 30 | 14 |
Drive Belt (14) |
| |
|
| |
between the |
|
|
front and rear |
|
|
pulleys. There | Top View | |
should be from | ||
1/4Ó to 1/2Ó of |
|
|
movement in |
| 54 |
the center of |
| |
| 29 | |
the Belt. If the |
| |
|
| |
Drive Belt (14) is |
|
|
properly adjusted, reattach the side shields and ped- als. If the Belt needs to be adjusted, loosen the Nylon Locknut (54) on the left side of the Flywheel (29). To tighten the Belt, turn the Adjustment Nut (30) clock- wise; to loosen the Belt, turn the Adjustment Nut counterclockwise. Make sure that the Flywheel is straight and tighten the Nylon Locknut (54). Reattach the side shields and pedals.
8