ProForm 831.23744.0 Maintenance and Troubleshooting, Battery Replacement, HOW to Adjust the Belt

Page 21

MAINTENANCE AND TROUBLESHOOTING

Inspect and tighten all parts of the elliptical exerciser regularly. Replace any worn parts immediately.

To clean the elliptical exerciser, use a damp cloth and a small amount of mild soap. Important: To avoid damage to the console, keep liquids away from the console and keep the console out of direct sunlight.

BATTERY REPLACEMENT

If the console displays become dim, the batteries should be replaced; most console problems are the result of low batteries. See assembly step 5 on page 8 for replacement instructions.

HANDGRIP PULSE SENSOR TROUBLESHOOTING

If the handgrip pulse sensor does not function proper- ly, see step 5 on page 16.

HOW TO ADJUST THE REED SWITCH

If the console does not display correct feedback, the reed switch should be adjusted. First, remove all of the screws from both side shields; there are three sizes of screws in the side shields—note which size of screw you remove from each hole. Then, gently pry the side shields away from the frame.

Next, locate the

 

 

 

Reed Switch (58).

 

 

 

Turn the Left

58

41

26

Pedal Disc (26)

 

84

 

until the Magnet

 

 

(41) is aligned

 

 

 

with the Reed

 

 

 

Switch. Loosen,

 

 

 

but do not

 

 

 

remove, the indi-

 

 

 

cated M4 x

 

 

 

16mm Screw

 

 

 

(84). Slide the

 

 

 

Reed Switch slightly closer to or away from the Magnet, and then retighten the Screw. Rock the Left Pedal Disc forward and backward just enough that the Magnet passes the Reed Switch repeatedly. Repeat

until the console displays correct feedback. When the Reed Switch is correctly adjusted, reattach the side shields. Note: If you have questions as to which screw should be in which hole, see EXPLODED DRAWING B on page 27 and the PART LIST on page 24.

HOW TO ADJUST THE BELT

If you can feel the pedals slip while you are pedaling, even when the resistance of the pedals is at the high- est setting, the Belt (46) may need to be adjusted.

First, remove all the screws from both side shields; there are three sizes of screws in the side shields—note which size of screw you remove from each hole. Then, gently pry the side shields away from the frame.

Next, turn the

 

Belt Adjustment

 

Screw (72) until

46

the Belt (46) is

 

tight. Then, reat-

 

tach the side

 

shields. Note: If

 

you have ques-

 

tions as to which

72

screw should be

in which hole,

 

see EXPLODED

 

DRAWING B on page 27 and the PART LIST on page 24.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Sears, Roebuck and Co., Hoffman Estates, IL Model No Serial NoTable of Contents Important Precautions Before YOU Begin M10 x 35mm Shoulder M10 x 70mm Button Screw AssemblyRepeat this step for the Left Frame Cover Attach the other Wheel 50 in the same wayScrews yet Avoid pinching Wire Harness During this stepAvoid pinching Wires during This step Tip Be careful not to pinch the wires during this stepPage Repeat this step for the other Pedal Arm Axle not shown 124 HOW to USE the Elliptical Exerciser HOW to Move the Elliptical ExerciserHOW to Exercise on the Elliptical Exerciser HOW to Change the Incline of the Ramp HOW to Adjust the Stride of the Elliptical ExerciserFeatures of the Console Console DiagramSelect the manual mode HOW to USE the Manual ModeTurn on the fan if desired HOW to USE a Cross Training WorkoutTurn on the console. See on Select a cross training workout Begin pedaling to start the workoutContinue the cross training workout Perform the first strength exercise when promptedTurn on the console. See on Select a calorie goal workout HOW to USE a Calorie Goal WorkoutTurn on the console. See on Select a target toning workout HOW to USE a Target Toning WorkoutHOW to USE the High Performance Workout Battery Replacement Maintenance and TroubleshootingHandgrip Pulse Sensor Troubleshooting HOW to Adjust the Reed SwitchExercise Intensity Exercise GuidelinesWorkout Guidelines Exercise FrequencySuggested Stretches Qty Description R1107AQty Description Exploded Drawing A-Model No Drawing Get it fixed, at your home or ours DAY Full Warranty
Top Page Image Contents