JVC GVT0004-003A, CA-D702T manual Getting Ready to Use Dolby 3 Channel Logic, Using Dolby Surround

Page 20

English

or

SHIFT

3CH LOGIC

\

CENTER MODE

TEST TONE

–CENTERLEVEL +

TEST TONE

or

PRO LOGIC

SHIFT	\
	\	3CH LOGIC
	\

Getting Ready to Use Dolby 3 Channel Logic

Speaker Arrangements for Dolby 3 Channel Logic ————

	Front					TV				Front
	Speaker									Speaker
	Speaker		Center Speaker							Speaker

Setting-up Dolby 3ch Logic ————————————————

1.Press PRO LOGIC/3CH LOGIC to select 3CH LOGIC.

Each time you press the button, Dolby Surround programs change as follows:

=PRO LOGIC =3CH LOGIC =OFF =(back to the beginning)

When using the Remote Control, press SHIFT then press the 3CH LOGIC (2).

•Perform the steps below using the buttons on the Remote Control.

2.Select the desired Center Speaker mode.

Press SHIFT on the Remote Control then press CENTER MODE (6). Each time you press the button, Center Speaker modes change as follows:

=NORMAL = WIDE = OFF = (back to the beginning)

3.Set the volume to the level you like.

4.Press TEST TONE (3).

A test tone comes out of the speakers in the following order:

•When “OFF” is selected for Center Speaker mode, no test tone comes out of the center speaker.

=LEFT = CENTER = RIGHT = (back to the beginning)

5. Adjust the level for the center speaker.

Press CENTER LEVEL + (5) or – (4). Set the level so that it is about the same as the level from the front speakers.

•You cannot adjust the level for the center speaker if “OFF” is selected for Center Speaker mode.

6.Press TEST TONE (3) again.

Test Tone mode is canceled.

This completes the preparations required for using Dolby 3 Channel Logic.

•You cannot adjust the Delay Time or rear speaker levels in Dolby 3 Channel Logic mode.

Using Dolby Surround

1.Press PRO LOGIC/3CH LOGIC and select the desired mode.

If you are using the Remote Control, press PRO LOGIC (1) or 3CH LOGIC (2) after pressing SHIFT. Make sure that the center speaker and rear speakers have been set up correctly, as described on pages 14 to 16.

2.Playback as source with the mark.

Enjoy the great sound achieved through Dolby Surround.

To Cancel Dolby Surround Effects

Press PRO LOGIC/3CH LOGIC until the Dolby Surround indicator goes out. If you are using the Remote Control, press the Dolby Surround buttons (PRO LOGIC (1) or 3CH LOGIC (2)) after pressing SHIFT.

16

Image 20

Contents CA-D702T If in Doubt Consult a Competent Electrician Class Laser Product Precaución el aparato debe estar bien ventilado Precaução Ventilação adequadaFeatures Installation of the UnitPower cord How This Manual Is OrganizedTable of Contents Accessories Setting the Voltage Selector SwitchHow to Put Batteries in the Remote Control Using the Remote ControlConnecting the FM Antenna Connecting the AM AntennaUsing the Supplied Wire Antenna Using an FM 75-Ohm Antenna Cable not suppliedRight Speaker Connecting the SpeakersConnecting the Optional Speakers Connecting Auxiliary Equipment On the Remote ControlVCR or other equipment On the UnitDisplay Demo ModeCommon Operations Setting the Clock Turning the Power On and OffAdjusting the Volume Turning the System OnBalance Adjustment Reinforcing the Bass SoundFor private listening Press Shift Press Balance L 10 or R +10Customizing a Sound Mode Sound ModesWhen a Rear Speaker is Connected Adjusting the Rear Speaker LevelUse Multi Control to adjust to any Sound Mode desired FrontTurn down the volume level to Press AUX Listening to Auxiliary Equipment3CH Logic Accessing the Dolby Surround FunctionsDolby Surround Center Speaker Mode Delay Time ModeAdjusting the level of the Center Speaker Adjusting the level of the Rear Speakers for PRO Logic onlySpeaker Arrangements for Dolby Pro Logic Setting-up Dolby Pro LogicGetting Ready to Use Dolby Pro Logic Using Dolby Surround Setting-up Dolby 3ch LogicGetting Ready to Use Dolby 3 Channel Logic Speaker Arrangements for Dolby 3 Channel LogicSetting the AM Tuner Interval Spacing Using the TunerTuning in a Station Three Ways to Select a Station Presetting StationsSwitching between Frequency Bands Changing the FM Reception Mode Using the CD Player Entering CD Operation Mode with the Remote ControlDisc indicator CD indicatorPlaying a CD Basics of Using the CD Player Continuous PlayLoading CDs Locating a Track with the Remote Control Directly Selecting a TrackFast Forward / Reverse Changing Discs While PlayingOn the Remote Control Press PROGRAM/RANDOM on the Unit Programing the Playing OrderTracks On the Unit Press PROGRAM/RANDOMRandom Play Checking the ProgramChanging the Program Press the number keys 1 to 10 and +10 to select the tracksRepeating a Track or the Discs Tray Lock FunctionLocking the Trays Unlocking the TraysTape ª £ Using the Cassette DeckEntering the Tape Operation Mode with the Remote Control Regular Play Music ScanFast Left and Fast Right Finding the Beginning of the Current SelectionReverse Mode Reverse Mode on Reverse Mode OFFRecording Things to Know before You Start RecordingStandard Recording Check the recording direction for the tapePress Tape Control then press To pause at any time during the recording processRecording AM Station to Tape CD Direct RecordingAuto Edit Recording How to Use Dubbing Tape to Tape Recording DubbingPress Dubbing To stop dubbing, press 7STOPUsing the Timer Setting the Daily Timer Press TIMER/CLOCK againSet the time you want the Unit to turn on Set the time you want the Unit to turn offTurning the Daily Timer On and Off Setting the Volume LevelTo change the Daily Timer setting To use a Cassette Deck as the sourceSetting the Recording Timer Setting the Sleep Timer Turning the Recording Timer On and OffTo change the Sleep Timer setting To cancel the Sleep Timer settingTimer Priority Example Setting OperationRecording Timer Sleep TimerUsing the Microphone Karaoke Sing AlongSound Display Singing Along with KaraokeRecording Your Singing Press FM MODE/ECHO on the Remote ControlDigital Echo Microphone Mixing Playing the Microphone Sound through the SpeakersRecording Microphone Mixing Recording from the MicrophoneCare and Maintenance Compact Discs Cassette TapesMoisture Condensation General NotesTroubleshooting SymptomPossible Cause ActionSpecifications Important for mains AC line