JVC RX-772VBK manual SOFT2 SOFT1 Flat SHARP1 SHARP2, Speakers, Front speakers

Page 31

Front panel

6.Press Control %/ Þuntil “–DELAY +” appears on the display.

7.Press Control @/ #to adjust the delay time of the rear speaker output. Each time you press the button, the delay time changes as follows:

DELAY 1

 

DELAY 2

 

DELAY 4

 

DELAY 3

 

DELAY 1:

Select this when the distance from you to your rear speakers is greater than that to the front

 

speakers.

 

 

DELAY 2:

Select this when the distance from you to your rear speakers is almost equal to that to the

 

front speakers.

 

 

DELAY 3:

Select this when the distance from you to your rear speakers is a little less than that to the

 

front speakers.

 

 

DELAY 4:

Select this when the distance from you to your rear speakers is much less than that to the

 

front speakers.

 

 

Note:

When you have selected “3CHLOGIC,” you cannot adjust the delay time.

8. Press Control %/ Þuntil “TEST” appears on the display, then press Control @/ #to start checking the speaker output balance.

“TEST” starts flashing on the display, and a test tone comes out of the speakers in the following order:

 

Left front speaker

 

 

Center speaker

 

Right front speaker

 

 

 

 

 

 

 

 

 

Rear speakers

 

 

 

 

 

 

 

 

 

 

 

Notes:

•No test tone comes out of the rear speakers when you have selected “3CHLOGIC.”

•No test tone comes out of the center speaker when you select “PHANTOM” or “OFF” for the center mode.

9.If necessary, adjust the speaker output balance as follows:

•To adjust the rear speaker output level, press Control %/ Þuntil “– REAR +” appears on the display, then press Control @/ #.

•To adjust the center speaker output level, press Control %/ Þ until “–CENTER+” appears on the display, then press Control @/ #.

Notes:

•You cannot adjust the left and right rear speakers output level separately.

•You cannot adjust the rear speakers output level when you have selected “3CHLOGIC.”

•You cannot adjust the center speaker output level when you select “PHANTOM” or “OFF” for the center mode.

10. Press Control %/ Þuntil “TEST” appears on the display, then press Control @/ #to stop the test tone.

11.Press Control %/ Þ until “CNT TONE” (Center Tone) appears on the display.

12.Press Control @/ #to select the center tone you want.

The center tone adjustment affects the mid-frequency range, which the human voice is mostly made up of.

Each time you press the button, the display changes to show the following:

SOFT2 SOFT1 FLAT SHARP1 SHARP2

To make the dialogue clearer, select “SHARP1” (little) or “SHARP2” (much).

To make the dialogue softer, select “SOFT1” (little) or “SOFT2” (much).

When “FLAT” is selected, no adjustment is applied.

Note:

The center tone cannot be adjusted when sounds do not come out of the center speaker.

Page 28

Page 30 Page 32
Image 31
Page 30 Page 32
Contents RX-772VBK To Reduce the Risk of Electric Shock Wide Normal Phantom OFF Table of Contents Checking the Supplied Accessories Before InstallationGetting Started Front Panel Switches, Buttons and ControlsRemote Control Unit Remote ControlFM Antenna Connections Connecting the FM and AM AntennasAM Antenna Connections Connecting the front speakers Connecting the SpeakersClose the terminal Connecting the rear and center speakersConnecting the subwoofer speaker Open the terminal and then insert the speaker signal cableIf your audio components have a Compu LINK-3 terminal Connecting Audio/Video ComponentsAudio component connections Audio Components Video ComponentsIf your video components have an AV Compu Link terminal Video component connectionsPutting Batteries in the Remote Control Connecting the Power CordR03 UM-4/AAA 24F Basic Operations Turning the Power On and OffSelecting the Source to Play Selecting the Front Speakers Adjusting the VolumeOn the front panel only Muting the Sound Listening with HeadphonesRecording a Source Adjusting the Front Speaker Output Balance Basic SettingsListening at Low Volume Loudness To cancel the Sleep Timer Using the Sleep TimerFrom the remote control Press Sleep repeatedly Small Selecting the Center Speaker SizeLarge Small no LargeExamples Using Visual ConfirmationOne Touch Operation Using the One Touch OperationTo store the sound settings Press ONE Touch Operation To cancel the One Touch Operation functionReceiving Radio Broadcasts Tuning in Stations ManuallyUsing Preset Tuning To store the preset stationsMono Selecting the FM Reception ModeTo tune in a preset station AutoAvailable characters Assigning Names to Preset StationsWhen a character you want appears, press Control #or @ Press Control %/ Þto select a characterSelecting Your Favorite SEA Mode Using the SEA ModesRock Musical Movie Country SEA OFF Usermode Jazz 100 1k 10k Creating Your Own SEA ModeTo recall your own SEA adjustment To erase a stored adjustmentPrologic 3CHLOGIC Hall Surr OFF Using the Surround ProcessorUsing JVC’s Hall Surround What is surround?Delay 1 Delay Delay 4 Delay DelayDelay Front Speaker Rear Speaker Speaker arrangements for Dolby SurroundFront Speaker Rear Speaker Center Speaker This caseWide Normal Phantom Preparing for Dolby SurroundFront speakers If necessary, adjust the speaker output balance as followsSOFT2 SOFT1 Flat SHARP1 SHARP2 SpeakersPress Test again to stop the test tone Press Test to start checking the speaker output balanceRemote Control Surround Off Using Dolby SurroundMenu function buttons Using the On-Screen Display to Control the ReceiverFrom the remote control Press Menu Press %/ Þto move To SETTING, then press @ / #Listening at Low Volume Loudness Also see Press %/ Þto move to SEA, then press @/ # Press %/ Þto move To SEA Adjust then press @/ #Press %/ Þ/ @ / # to adjust the SEA mode as you want Press %/ Þto move to TUNER, then press @/ #For Dolby Pro Logic Press %/ Þto move to Surround ADJUST, then press @ / #Press %/ Þto move To SURROUND, then press @/ # Press %/ Þ to move to one of the surround modesAutomatic Source Selection Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver CD player Cassette deckWhen using a VHS VCR, connect it as follows See also AV Compu Link Remote Control SystemTo video input 1 S-video jack using S-video cable To video input 2 jack using video cableAutomatic Power On/Off Automatic Selection of TV’s Input ModeOne-Touch Video Play CD player-changer TunerSound control section Amplifier CD playerCassette deck Turntable10, 0, +10 TV/CATV/SAT PowerTV Volume + Channel +Try to operate your VCR by pressing VCR Power VCR PowerManufacturers’ codes for TV Yamaha 019 Zenith 016 056, 177Manufacturers’ codes for Catv converters Manufacturers’ codes for VCR Manufacturers’ codes for satellite tunerXR-1000 000, 035 Yamaha 038 Zenith 033, 034 149, 212Problem Possible Cause TroubleshootingAmplifier SpecificationsVideo AM tuner FM tuner IHFGeneral Factory Service Center Locations QualityserviceIf you ship the product Limited Warranty AUDIO-2 0497OFYOTKJEM

RX-772VBK specifications

The JVC RX-772VBK is a versatile home theater receiver designed to deliver an immersive audio experience for music and movie enthusiasts alike. With a user-friendly interface and an array of cutting-edge features, the RX-772VBK stands out as a robust choice for those looking to enhance their home entertainment system.

One of the most notable features of the RX-772VBK is its powerful amplification. With a robust output of 100 watts per channel, this receiver can drive a wide range of speakers and produce clear, dynamic sound at any volume level. Whether it’s blasting your favorite music or creating a rich soundscape for movies, the RX-772VBK handles it with ease.

Connectivity is another key area where the RX-772VBK shines. It includes multiple HDMI inputs, allowing you to connect various devices such as Blu-ray players, gaming consoles, and streaming devices seamlessly. The receiver supports 4K video pass-through, ensuring that your high-definition content looks its best. Additionally, it features built-in Bluetooth technology, enabling users to wirelessly stream music from smartphones, tablets, or laptops.

The RX-772VBK also incorporates advanced audio processing technologies. It includes Dolby TrueHD and DTS-HD Master Audio support, which provides a cinematic surround sound experience that envelops listeners. The receiver comes with a built-in equalizer, giving users the ability to tailor sound output to their personal preferences and the acoustics of their viewing room.

Ease of use is a defining characteristic of the RX-772VBK. The intuitive on-screen setup guide simplifies installation, while the remote control provides straightforward access to settings and input selection. The receiver also features a sleep timer and customizable sound modes, enhancing user experience even further.

In addition to its performance, the RX-772VBK is designed with aesthetics in mind. Its sleek, black finish and modern design ensure that it complements any home decor, making it a welcome addition to your living space.

In summary, the JVC RX-772VBK is an impressive home theater receiver that brings together strong amplification, versatile connectivity, and advanced audio technologies. Whether you’re watching movies, listening to music, or gaming, this receiver promises to elevate your audio experience to new heights.
Top Page Image Contents