JVC RX-772VBK manual Using the On-Screen Display to Control the Receiver, Menu function buttons

Page 34

Using the On-Screen Display to Control the Receiver

You can use the menu function on the TV screen to control the receiver.

To use this function, you need to connect the TV to the MONITOR OUT jack on the rear panel (see page 9), and set the TV’s input mode to the appropriate position to which the receiver is connected.

When the TV’s input mode is for TV, you cannot see the on-screen display.

IMPORTANT:

When you use the menu functions, make sure that you have connected a TV and operate the menu function while watching the on-screen displays on the TV.

Basic Procedures

Menu function buttons

 

 

 

CONTROL

 

 

 

 

TAPE

VCR

 

MENU

 

 

 

 

MENU

EXIT

 

 

 

 

 

 

O

 

 

 

 

 

L

N

S

 

 

 

 

O

 

 

 

T

 

 

C

 

N

R

 

 

R

 

 

 

 

 

EEN CO

 

 

MAIN MENU

From the remote control:

1.Press MENU.

The MAIN MENU appears on the TV screen.

•If you press %/ Þ/ @/ #, a sub-menu you can adjust at that time appears on the TV screen instead of the MAIN MENU.

2.Press %/ Þto move to the sub-menu you want to set, then press @/ #. The sub-menu you want appears.

3.If necessary, press % / Þ/ @/ #to set or adjust the item you want on the selected sub- menu.

When a item is selected, the item will be highlighted.

Note:

Moving to an item does not mean that you have selected it. If the item is not highlighted, press @/ #to highlight it.

4.When you finish, press MENU EXIT. The menu disappears from the TV.

To go back to the MAIN MENU any time during the process

Press MENU again.

Shows the buttons you can use on the current menu. In this case, press % / Þ to move up and down, and @ / # to select the item. (The menus are shown on the TV for about one minute.)

Selecting the Source to Play (Also see page 11)

1.Press MENU.

The MAIN MENU appears on the TV.

2. Press %/ Þto move to “SOURCE,” then press @/ #.

The SOURCE menu appears.

3.Press %/ Þ to move to the source you want to play.

4.When you finish, press MENU EXIT. The menu disappears from the TV.

Adjusting the Front Speaker Output Balance (Also see page 14)

1.Press MENU.

The MAIN MENU appears on the TV.

2. Press %/ Þto move

to “SETTING,” then press @ / #.

The SETTING menu appears.

3.Press %/ Þto move to “BAL.” (Balance).

4.Press @/ #repeatedly to adjust the balance.

5.When you finish, press MENU EXIT. The menu disappears from the TV.

SOURCE menu

SETTING menu

Shows the buttons you can use on the current menu.

In this case, press % / Þ to

move up and down, and @ / # to adjust or set the item.

Page 31

Page 33 Page 35
Image 34
Page 33 Page 35
Contents RX-772VBK To Reduce the Risk of Electric Shock Wide Normal Phantom OFF Table of Contents Checking the Supplied Accessories Before InstallationGetting Started Switches, Buttons and Controls Front PanelRemote Control Remote Control UnitFM Antenna Connections Connecting the FM and AM AntennasAM Antenna Connections Connecting the Speakers Connecting the front speakersOpen the terminal and then insert the speaker signal cable Connecting the rear and center speakersConnecting the subwoofer speaker Close the terminalAudio Components Video Components Connecting Audio/Video ComponentsAudio component connections If your audio components have a Compu LINK-3 terminalVideo component connections If your video components have an AV Compu Link terminalPutting Batteries in the Remote Control Connecting the Power CordR03 UM-4/AAA 24F Basic Operations Turning the Power On and OffSelecting the Source to Play Selecting the Front Speakers Adjusting the VolumeOn the front panel only Muting the Sound Listening with HeadphonesRecording a Source Adjusting the Front Speaker Output Balance Basic SettingsListening at Low Volume Loudness To cancel the Sleep Timer Using the Sleep TimerFrom the remote control Press Sleep repeatedly Large Selecting the Center Speaker SizeLarge Small no SmallUsing Visual Confirmation ExamplesTo cancel the One Touch Operation function Using the One Touch OperationTo store the sound settings Press ONE Touch Operation One Touch OperationTo store the preset stations Tuning in Stations ManuallyUsing Preset Tuning Receiving Radio BroadcastsAuto Selecting the FM Reception ModeTo tune in a preset station MonoPress Control %/ Þto select a character Assigning Names to Preset StationsWhen a character you want appears, press Control #or @ Available charactersSelecting Your Favorite SEA Mode Using the SEA ModesRock Musical Movie Country SEA OFF Usermode Jazz To erase a stored adjustment Creating Your Own SEA ModeTo recall your own SEA adjustment 100 1k 10kWhat is surround? Using the Surround ProcessorUsing JVC’s Hall Surround Prologic 3CHLOGIC Hall Surr OFFDelay 1 Delay Delay 4 Delay DelayDelay This case Speaker arrangements for Dolby SurroundFront Speaker Rear Speaker Center Speaker Front Speaker Rear SpeakerPreparing for Dolby Surround Wide Normal PhantomSpeakers If necessary, adjust the speaker output balance as followsSOFT2 SOFT1 Flat SHARP1 SHARP2 Front speakersPress Test to start checking the speaker output balance Press Test again to stop the test toneUsing Dolby Surround Remote Control Surround OffPress %/ Þto move To SETTING, then press @ / # Using the On-Screen Display to Control the ReceiverFrom the remote control Press Menu Menu function buttonsListening at Low Volume Loudness Also see Press %/ Þto move to TUNER, then press @/ # Press %/ Þto move To SEA Adjust then press @/ #Press %/ Þ/ @ / # to adjust the SEA mode as you want Press %/ Þto move to SEA, then press @/ #Press %/ Þ to move to one of the surround modes Press %/ Þto move to Surround ADJUST, then press @ / #Press %/ Þto move To SURROUND, then press @/ # For Dolby Pro LogicCD player Cassette deck Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Automatic Source SelectionTo video input 2 jack using video cable AV Compu Link Remote Control SystemTo video input 1 S-video jack using S-video cable When using a VHS VCR, connect it as follows See alsoAutomatic Power On/Off Automatic Selection of TV’s Input ModeOne-Touch Video Play CD player TunerSound control section Amplifier CD player-changerTurntable Cassette deckChannel + TV/CATV/SAT PowerTV Volume + 10, 0, +10VCR Power Try to operate your VCR by pressing VCR PowerManufacturers’ codes for TV Yamaha 019 Zenith 016 056, 177Manufacturers’ codes for Catv converters Manufacturers’ codes for satellite tuner Manufacturers’ codes for VCR149, 212 XR-1000 000, 035 Yamaha 038 Zenith 033, 034Troubleshooting Problem Possible CauseAmplifier SpecificationsVideo AM tuner FM tuner IHFGeneral Factory Service Center Locations QualityserviceIf you ship the product Limited Warranty AUDIO-2 0497OFYOTKJEM

RX-772VBK specifications

The JVC RX-772VBK is a versatile home theater receiver designed to deliver an immersive audio experience for music and movie enthusiasts alike. With a user-friendly interface and an array of cutting-edge features, the RX-772VBK stands out as a robust choice for those looking to enhance their home entertainment system.

One of the most notable features of the RX-772VBK is its powerful amplification. With a robust output of 100 watts per channel, this receiver can drive a wide range of speakers and produce clear, dynamic sound at any volume level. Whether it’s blasting your favorite music or creating a rich soundscape for movies, the RX-772VBK handles it with ease.

Connectivity is another key area where the RX-772VBK shines. It includes multiple HDMI inputs, allowing you to connect various devices such as Blu-ray players, gaming consoles, and streaming devices seamlessly. The receiver supports 4K video pass-through, ensuring that your high-definition content looks its best. Additionally, it features built-in Bluetooth technology, enabling users to wirelessly stream music from smartphones, tablets, or laptops.

The RX-772VBK also incorporates advanced audio processing technologies. It includes Dolby TrueHD and DTS-HD Master Audio support, which provides a cinematic surround sound experience that envelops listeners. The receiver comes with a built-in equalizer, giving users the ability to tailor sound output to their personal preferences and the acoustics of their viewing room.

Ease of use is a defining characteristic of the RX-772VBK. The intuitive on-screen setup guide simplifies installation, while the remote control provides straightforward access to settings and input selection. The receiver also features a sleep timer and customizable sound modes, enhancing user experience even further.

In addition to its performance, the RX-772VBK is designed with aesthetics in mind. Its sleek, black finish and modern design ensure that it complements any home decor, making it a welcome addition to your living space.

In summary, the JVC RX-772VBK is an impressive home theater receiver that brings together strong amplification, versatile connectivity, and advanced audio technologies. Whether you’re watching movies, listening to music, or gaming, this receiver promises to elevate your audio experience to new heights.
Top Page Image Contents