STEP#2 Sensorweightbarinstallation | ProSpot Fitness P-100 guide

o_ Plugtogetherbothof the BaseRailWire Harness(8) to lowerendsof the SpiralSignalCables(46)located just underthe perforatedSliderShieldson backof the ScreenPanels(53).

7 . Attachthetwo RearSupportRails(4)to the LowerCrossBrace(3)andthe CrossBraceBackingPlates(13) usingfourbolts(28),eightwashers(18)andfournuts(20)as shown.HANDTIGHTENthe boltsat thistime.

LAttachthe two Big Pulleys(27)to the two UpperLinkingPlates(17)usingtwo bolts(19),fourwashers(23) andtwo nuts(26)as shown.HANDTIGHTENthe boltsat thistime.

9 . Liftthe UpperLinkingPlatesAssembly(17 & 271andplaceit on top of the LeftUprightGuidepostAssembly (9, 12,53),andattachthe two UpperLinkingPlates(17)to the LeftUprightGuidePost(12)usingtwo bolts (22),fourwashers(18)andtwo nuts(20)as shown.HANDTIGHTENthe boltsat thistime.

'10.
Carefullyflexthe LeftWeightBar Cables(24)ontothe pulleys(27)so thatthe cablesinsertintothe grooves
pulleys
of eachcorresponding	andallowingthe LeftWeightBar Knuckle(44)to hangfree.Be sure that the

cablesare straightand uncrossedand cablesand pulleysmove smoothly.

11. Alignthe holeson top of the RearSupportRail(4) withthe correspondingholeson the two UpperLinking Plates('17)andattachthe RearSupportRail(4)to the LinkingPlates(17)usingtwo bolts(22),fourwashers (18)andtwo nuts(20)as shown.HANDTIGHTENthe boltsat thistime.

12.Repeatthe steps8 - 11 on the rightsideof the PROSPOTT/rressrM-'l00.

13.Attachthe UpperCrossBrace(11)to the four UpperlinkingPlates(17)usingfourbolts(22),eightwashers (18)andfournuts(20)as shown.HANDTIGHTENthe boltsat thistime.

14.Tightenall bolts and nuts used for assemblyin previoussteps.

STEP#2: SENSORWEIGHTBARINSTALLATION

1.Standingin front of the PROSPOTlaessrM-100.Insertone end and then the otherend of the Sensor WeightBar (25)intothe Knuckles(42 & 44).Slidethe knucklesontothe Bar untrltheyrestsnuglyagainst the preinstalledsensorretainingcollars(45 & 48) at eachend of the SensorWeightBar (25).(Thereis a rotationlimitingpin thatprotrudesfromthe bottomof the SensorWeightBar(25)thatmustfit througha slot in the knucklesU2 & 44\as it is slidintoposition).

2.Placeone PlasticLockingSleeve(39)ontoeachendof the SensorWeightBar(25)andslidetheminwards untiltheybuttup againstandsecuretheWeightBarCableKnucklein place.TightenPlasticLockingSleeve boltssecurely.

3.Placeone of the OlympicAdapters(30)ontothe SensorWeightBar (25)and slidethemontothe Bar until theytouchthe PlasticLockingSleeves(39).lnsertan OlympicAdapterRetainingPlug(33)ontoeachend

of the SensorWeightBar (25) so that theyalso go insideof the OlympicAdapters(30).Securewith two Allenbolts(29)andtwowashers(36).

4.Attachthe four smallplasticpipes(15) to the four UpperlinkingPlates(17) usingfour bolts(34),eight washers(38)andfour nuts(35)as shown.Tightenthe boltssecurely.

5.Attach the ElectronicBox Locating Board (40) to the Lower Cross Brace (3) using two bolts (22), tour washers(18)andtwo nuts(20)as shown.Tightenthe boltssecurely.

6.Attachthe six SideWeightPlateHolders(14)to the RearSupportRails(4) usingsix backingplates(16), twelvebolts(22),twenty-fourwashers(18)andtwelvenuts(20)as shown.Tightenthe boltssecurely.

Note:In this manualwhenreferringto Leftand Rightsideof unit,the leftandrightperspective are from the outside,facingthe front of the unit.

--2--