Weider WEBE63990 manual Tighten the M10 Nylon Locknuts 11 used in steps 10, Right Side Left

Page 10

12.Orient the Crossbar (20) with the warning decal fac- ing up as shown. Attach a Barbell Post (35) to the Crossbar with two M10 x 68mm Bolts (33), a Support Plate (16) and two M10 Nylon Locknuts (11).

Attach the second Barbell Post (35) to the Crossbar

(20)in the same manner. Note: Make sure both

Barbell Posts are oriented with the high side of the bracket pointing in the same direction.

13.Note: Make sure the two upright assemblies have the Nylon Locknuts on the side facing the center of the bench, as described in steps 10 and 11.

Attach the Crossbar (20) to the right upright assembly

(A) with two M10 x 68mm Bolts (33), a Support Plate (16) and two M10 Nylon Locknuts (11). Make sure the Bolts are inserted from the side shown in the upper inset drawing.

Attach the Crossbar (20) to the left upright assembly

(B)with two M10 x 68mm Bolts (33), a Support Plate (16) and two M10 Nylon Locknuts (11). Make sure the Bolts are inserted from the side shown in the lower inset drawing.

Tighten the M10 Nylon Locknuts (11) used in steps 10 and 11.

14.Press a 1Ó Inner Cap (32) into the open end of each Weight Rest (21, 52) and each Safety Spotter (26,

53). Insert each Weight Rest and Safety Spotter into one of the adjustment holes in the Uprights (1). Note:

There is a Left Weight Rest (21) and a Right Weight Rest (52) because the locking clip should be on the outside of the Upright. The same is true for the Left and Right Safety Spotter (26, 53).

Warning: Always insert both Weight Rests at the same height. Always insert both Safety Spotters at the same height. Make sure the locking clips snap into place around the Uprights.

15.Attach the Curl Pad (29) to the Curl Post (42) with two M6 x 16mm Screws (3).

12

35

High Side of Bracket

 

 

 

33

33

 

35

 

 

 

 

 

16

20

 

33

 

 

 

 

 

 

 

 

Decal

 

11

16

 

 

 

 

 

 

 

 

11

 

 

13

33

 

16

A

 

 

 

Right

 

 

 

11

Side

 

 

 

 

A

 

 

 

20

 

 

 

11

 

 

 

 

 

 

 

 

B

 

 

 

 

Left

 

 

 

 

Side

11

 

 

 

 

 

20

 

 

 

 

 

B

 

 

11

 

33

 

 

 

 

 

 

 

16

 

 

 

14

 

15

 

29

 

 

 

 

 

32

 

 

 

21

 

 

 

 

Locking

Clip

 

32

3

 

 

26

1

3

 

42

 

 

10

Image 10
Contents Mon.ÐFri., 6 a.m.Ð6 p.m. MST Model No. WEBE63990 Serial NoCustomer HOT Line Patent PendingTable of Contents Important Precautions Right Side Before You BeginLeft Side Part Identification Chart Model No. WEBE63990 R0899A Assembly Make Things Easier for YourselfLubricate Page Locknuts yet Nylon Locknuts yetTighten the M10 Nylon Locknuts 11 used in steps 10 Right Side LeftUsing the Weight Rests and Curl Barbell Adjusting the Weight BenchAdjusting the Foam Pads Setting UP the Bench for Squat Exercises Adjusting the BackrestAttaching Weights to the LEG Lever Attaching the Curl PostExercise Guidelines Cooling Down Staying MotivatedAerobic Exercise Exercise Weight Sets RepsDate Thursday Aerobic Exercise DatePart List Model No. WEBE63990 Qty DescriptionExploded Remove this Part LIST/EXPLODED Drawing from the Manual Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT