Weider WEBE63990 manual Lubricate

Page 7

3.Attach the Bumper (41) to the Front Leg (19) with an M4 x 25mm Screw (43).

Press a 50mm Square inner Cap (17) into each open end of the Leg Lever (18). Press a 48mm Round Inner Cap (40) into the weight tube on the Leg Lever.

Lubricate the M10 x 75mm Bolt (44). Attach the Leg Lever (18) to the bracket on the Front Leg (19) with the Bolt and an M10 Nylon Locknut (11).

4.Press a 25.4mm x 38.1mm Inner Cap (28) into each end of both Backrest Tubes (27).

Press a 25.4mm x 38.1mm Inner Cap (28) into each open end of the tubes on the Backrest Adjustment Bracket (39).

Important: Before performing step 5, make sure the Backrest Tubes are oriented correctly. The holes marked in the drawing are not centered on the Tube; they are closer to one edge. This edge must be pointed towards the floor.

3

 

11

 

 

 

17

 

 

18

44

 

 

41

17

43

Lubricate

 

 

19

 

40

 

 

17

 

4

 

28

 

 

28

 

27

39

 

 

 

 

28

28

 

 

Holes are closer to one edge.

Point this edge towards the floor.

5.Slide an M10 Washer (6) onto an M10 x 193mm Bolt (22) and then slide the Bolt through the indicated hole in one Backrest Tube (27).

Make sure the Backrest Tube (27) is oriented as shown in the drawing. Slide the M10 x 193mm Bolt

(22)through the welded tube at the upper end of the Backrest Adjustment Bracket (39).

Slide the second Backrest Tube (27) onto the

M10 x 193mm Bolt (22). Secure the Backrest Tubes with an M10 Washer (6) and an M10 Nylon Locknut (11).

6.Slide an M10 Washer (6) onto an M10 x 193mm Bolt (22).

Place the backrest tube assembly onto the Bench Frame (5), so the lower end of the Backrest Adjustment Bracket (39) rests on one of the adjust- ment tabs.

Slide the M10 x 193mm Bolt (22) through the indicat- ed hole in one Backrest Tube (27), then through the welded tube on the Bench Frame (5) and finally through the other Backrest Tube. Secure the Bolt with an M10 Washer (6) and an M10 Nylon Locknut (11).

Do not overtighten the Nylon Locknut; it must be easy to pivot the Backrest Tubes.

7

5

 

 

22

6

Welded Tube

 

27

 

6

 

39

 

 

11

Holes

 

27

6

 

27

 

 

 

Welded

 

22

Tube

 

 

 

39

6

 

 

 

6

 

 

11

Adjustment

 

 

5

 

Tab

 

 

Image 7
Contents Patent Pending Model No. WEBE63990 Serial NoCustomer HOT Line Mon.ÐFri., 6 a.m.Ð6 p.m. MSTTable of Contents Important Precautions Right Side Before You BeginLeft Side Part Identification Chart Model No. WEBE63990 R0899A Make Things Easier for Yourself AssemblyLubricate Page Nylon Locknuts yet Locknuts yetRight Side Left Tighten the M10 Nylon Locknuts 11 used in steps 10Using the Weight Rests and Curl Barbell Adjusting the Weight BenchAdjusting the Foam Pads Attaching the Curl Post Adjusting the BackrestAttaching Weights to the LEG Lever Setting UP the Bench for Squat ExercisesExercise Guidelines Staying Motivated Cooling DownThursday Aerobic Exercise Date Exercise Weight Sets RepsDate Aerobic ExerciseQty Description Part List Model No. WEBE63990Exploded Remove this Part LIST/EXPLODED Drawing from the Manual Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT