Weider WESY85104 user manual ARM Assembly

Page 8

ARM ASSEMBLY

8.Press a 1 3/4” Square Inner Cap (44) into the top of a Press Arm (46). Press a 1” Round Inner Cap (49) into each end of the handle on the Press Arm. Attach the Press Arm to one side of the Press Frame (17) with two 5/16” x 2 1/2” Bolts (22) and two 5/16” Nylon Locknuts (3).

Assemble the other Press Arm (46) in the same manner.

9.Identify the Right Arm (48) and the Left Arm (47). Note the position of the welded bracket on each Arm. Arm identification is very important for step 10.

Note: The “V”-Pulleys (6), Long Cable Traps (50), 3/8” x 2 1/2” Bolts (7), and 3/8” Nylon Locknuts (21) are pre-attached. These have been shown disassembled for easy part iden- tification.

10.Lubricate both axles on the Top Frame (55).

Slide the Right Arm (48) onto the right axle.

Note: Be careful not to confuse the Right Arm with the Left Arm (47); refer to step 9 to identify the Right Arm. Be sure that the upper end of the Right Arm is behind the indicated bracket on the Top Frame (55).

Tap two 1” Retainers (69) and a 1” Round Cover Cap (70) onto the right axle. Be sure that the teeth on the Retainers bend toward the Cover Cap, as shown in the inset drawing.

Attach the Left Arm (47) in the same manner.

Press 1 3/4” Square Inner Caps (44) into the lower ends of the Right and Left Arms (47, 48). Wet the lower end of each Arm with soapy water. Slide a 10” Pad (45) onto the lower end of each Arm.

8

8

 

 

 

44

 

 

 

 

 

 

 

 

49

44

 

49

 

 

 

 

 

 

49

 

 

 

46

 

 

 

 

46

 

22

 

 

 

 

 

 

 

 

 

3

 

 

 

 

17

 

9

50

7

50

 

 

 

6

 

 

6

 

 

 

 

 

 

Welded

 

 

 

47

Brackets

 

 

 

 

 

 

21

 

48

 

 

 

 

10

 

 

 

 

 

 

55

 

47

 

 

 

 

 

 

 

Bracket

 

 

 

Lubricate

 

 

 

Axle

 

48

 

 

69

 

 

 

 

 

 

 

 

70

45

 

 

 

 

44

 

 

 

 

45

 

 

55

 

 

 

 

 

 

 

 

 

69

 

 

 

 

70

Image 8
Contents QUESTIONS? Customer HOT LineTable of Contents Important Precautions Using the Weider 8510 home gym system. If you Before YOU BeginFollowing Tools not Included are Required for Assembly AssemblyFrame Assembly Nylon Locknuts yet ARM ARM Assembly Cable Assembly Cable Assembly Complete the assembly of several pre Attached parts Cable Assembly Cable Assembly Seat Assembly Locknut. The Leg Lever must be able to Pivot freelySeat Assembly High Pulley Butterfly Adjustment Changing the Weight SettingAttaching the LEG Lever to the LOW Pulley Station Weight Resistance ChartAttaching and Removing the Seat Troubleshooting and Maintenance Tightening the CablesCable Diagram Page Part LIST-Model No. WESY85104 Exploded DRAWING-Model No. WESY85104 Part Identification CHART-Model No. WESY85104 R1102A Page Page Ordering Replacement Parts Limited Warranty