Weider WESY85104 user manual Cable Assembly

Page 10

CABLE ASSEMBLY

15. Route the Long Cable (23) around the “V”-

15

 

 

50

7

Pulley (6) on the Right Arm (48). Be sure

 

 

 

 

 

that the Cable is in the groove of the “V”-

 

 

 

 

6

 

 

 

 

 

Pulley and that the Long Cable Trap (50) is

 

 

 

 

 

turned to hold the Cable in place. Tighten

 

 

 

 

 

the 3/8” x 2 1/2” Bolt (7) and the 3/8” Nylon

 

 

 

 

 

Locknut (not shown).

 

 

 

 

 

 

 

 

 

 

48

 

 

 

23

 

 

16. Route the Long Cable (23) around the 3 1/2”

16

 

68

66

 

Pulley (15) attached to the Pulley Bracket

 

 

 

 

 

 

(20). Be sure that the Cable is in the

 

 

 

 

 

groove of the Pulley and that the Cable

 

 

 

 

 

Trap (66) is turned to hold the Cable in

 

20

 

 

 

place. Tighten the 3/8” x 2” Bolt (12) and the

 

 

 

 

 

3/8” Nylon Locknut (not shown).

 

12

 

 

 

 

 

 

 

 

Be sure that the 5/16” x 5” Bolt (68) is proper-

 

23

 

15

 

ly tightened and that the Pulley Bracket (20)

 

 

 

 

 

 

 

 

 

can move freely.

 

 

 

 

 

17. See the inset drawing. Attach a 3 1/2” Pulley

17

 

 

 

 

(15) and a Cable Trap (66) to the indicated

 

 

 

 

 

 

 

 

 

hole in the Long “U”-Bracket (57) with a 3/8” x

 

 

 

 

 

2” Bolt (12) and a 3/8” Nylon Locknut (21).Be

 

 

 

 

 

sure that the Cable Trap is inside the “U”-

 

 

 

 

 

Bracket. Note: This may come pre-assem-

 

 

 

 

 

bled.

 

23

 

 

23

 

 

 

 

 

 

 

 

 

Route the Long Cable (23) around the 3 1/2”

 

66

15

 

 

Pulley (15) and through the Long “U”-Bracket

 

12

 

 

(57). Be sure that the Cable is in the

 

 

 

 

 

21

 

 

 

groove of the Pulley and that the Cable

 

 

 

 

 

57

 

 

 

and Pulley move smoothly.

 

 

 

 

 

 

 

 

 

18. Note: The Pulley (15) in this drawing is

18

 

 

 

15

pre-assembled. It is shown disassembled

 

 

23

 

 

 

for easy part identification.

 

 

Bracket

12

 

 

 

 

 

Route the Long Cable (23) around the 3 1/2”

 

 

 

 

 

Pulley (15) attached to the bracket on the Top

 

 

55

 

 

Frame (55). Tighten the 3/8” x 2” Bolt (12)

 

 

 

 

 

 

 

 

 

and the 3/8” Nylon Locknut (21).Be sure that

 

 

 

 

 

the Cable is in the groove of the Pulley

 

 

 

 

 

and that the Cable and Pulley move

 

 

21

 

 

smoothly.

 

 

 

 

 

10

Image 10
Contents QUESTIONS? Customer HOT LineTable of Contents Important Precautions Using the Weider 8510 home gym system. If you Before YOU BeginFrame Assembly AssemblyFollowing Tools not Included are Required for Assembly Nylon Locknuts yet ARM ARM Assembly Cable Assembly Cable Assembly Complete the assembly of several pre Attached parts Cable Assembly Cable Assembly Seat Assembly Locknut. The Leg Lever must be able to Pivot freelySeat Assembly High Pulley Butterfly Adjustment Changing the Weight SettingAttaching and Removing the Seat Weight Resistance ChartAttaching the LEG Lever to the LOW Pulley Station Troubleshooting and Maintenance Tightening the CablesCable Diagram Page Part LIST-Model No. WESY85104 Exploded DRAWING-Model No. WESY85104 Part Identification CHART-Model No. WESY85104 R1102A Page Page Ordering Replacement Parts Limited Warranty