Weider WESY5983.3 user manual

Page 6

2.Attach a Wheel (31) to the outside of the Base (1) with an M10 x 108mm Bolt (81), three M10 Washers (75), and an M10 Nylon Locknut (76).

Do not overtighten the Locknut; the Wheel must be able to turn easily.

Attach the other Wheel (not shown) in the same manner.

3.Press a 38mm x 64mm Inner Cap (41) into each end of the Cross Tube (11).

Orient the Cross Tube (11) as shown, with the welded tubes at the bottom. Attach the Foot Plate (23) and the Cross Tube to the Upright (3) with two M10 x 140mm Carriage Bolts (73), two M10 Washers (75), and two M10 Nuts (47). Do not insert a bolt into the top hole in the Foot Plate yet.

4.Press two 57mm Round Outer Caps (27) onto the ends of the Front Leg (6).

Orient the Bench Rail (5) as shown. Slide the Rail Bracket (105) into the indicated end of the Bench Rail, and align the holes in the Bracket with the holes in the Bench Rail.

Orient the Front Leg (6) as shown. Attach the Front Leg to the Bench Rail (5) with the Rail Bracket (105), four M8 x 25mm Button Screws (46), and four M8 Split Washers (52).

5.See the inset drawing. Snap the Seat Knob (45) into the Seat Carriage (12) and attach it with two M6 x 16mm Screws (82) and two M6 Black Nylon Locknuts (69). Make sure the slot in the Knob is aligned with the slot in the Seat Carriage.

Orient the Seat (13) and the Seat Backing (9) as shown. Attach the Seat and the Seat Backing to the Seat Carriage (12) with four M6 x 16mm Screws (82).

2

 

 

 

 

 

 

 

 

 

 

76

 

75

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

75

 

 

 

 

 

 

 

 

81

 

 

 

1

31

 

 

 

 

 

 

 

3

 

 

 

 

 

 

 

23

 

3

41

 

 

 

 

 

 

 

 

75

47

 

 

 

 

 

 

 

41

73

 

 

 

 

 

11

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Welded

 

 

 

 

 

 

Tube

4

 

 

 

 

 

 

 

 

 

 

5

 

 

 

 

 

105

 

Holes

 

 

 

 

 

 

 

 

52

 

52

 

 

 

 

27

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

46

 

 

 

 

 

46

 

 

 

 

 

 

 

 

6

 

 

27

 

 

 

 

 

 

 

 

 

5

 

 

 

 

13

 

 

 

 

 

 

 

 

 

Round

 

9

 

 

 

 

End

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

12

 

 

12

 

 

 

 

 

 

 

 

 

 

Slot

 

 

 

82

82

 

 

82

45

69

6

Image 6
Contents Call TOLL-FREE QUESTIONS?Model No. WESY5983.3 Serial No Mon.-Fri., 6 a.m.-6 p.m. MSTTable of Contents Important Precautions Assembled Dimensions Before YOU BeginAssembly Make Things Easier for YourselfPage Page Page Do not overtighten the Locknut the Leg Lever Must be able to pivot easilyOnto the tubes. Repeat with the tube on Leg Developer Locate the Long Cable 80. Insert one end Swivel Arm. Make sure the Cable is on the indiFlat edge of the Pulley Guard is on the side Shown Arm 22. Make sure the Cable is on the indicat Ed side of the welded rod in the Swivel ArmPage Adjustments Adjusting the SeatAttaching the High Pulleys and LEG Lever Attaching the Accessories Adjusting the ResistanceAdjusting the Backrest Storing the Resistance SystemAdjusting the LEG Developer Cable DiagramUsing the Removable Resistance Bars Make sure the rings are pushed against the TrayExercise Guidelines Muscle Chart Cooling DownStaying Motivated Aerobic Exercise DateExercise Resistance Sets Reps Thursday Aerobic Exercise DatePart Identification Chart Page Part LIST-Model No. WESY5983.3 Qty DescriptionExploded DRAWING-Model No. WESY5983.3 Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT