Weider WESY5983.3 user manual

Page 8

9.Press two 38mm Round Inner Caps (38) into the ends of the Top Frame (10).

Attach two Eyebolts (34) to the Top Frame (10) with two M8 Washers (59) and two M8 Nylon Locknuts (65). Do not overtighten the Locknuts; the Eyebolts must be able to rotate freely.

Attach the Top Frame (10) to the Lat Tower (4) with two M10 x 65mm Button Head Screws (70), two M10 Washers (75), and the Top Frame Cover

(93).Make sure that the Eyebolts (34) are ori- ented as shown in the inset drawing. If they are not, turn the Top Frame around and reat- tach it.

10.Attach the two 10-pound Short Resistance Caps

(20)to the 10-pound Center Resistance Bar (44) with two M4 x 12mm Flat Head Screws (85).

Using ten M4 x 12mm Flat Head Screws (85), attach the two 10-pound Resistance Caps (101) to the 10-pound Removable Resistance Bar (67), the two 20-pound Resistance Caps (88) to the

20-pound Removable Resistance Bar (36), the four 80-pound Resistance Caps (100) to the two 80-pound Resistance Bars (95), and the two 40- pound Resistance Caps (79) to the 40-pound Resistance Bars (96).

11.Locate the Fulcrum (18) on the Lat Tower (4) (see the inset drawing). Slide the Tray (35) onto the rods on the Fulcrum. Make sure the Tray is ori- ented as shown in the drawing.

Set the Resistance Bars into the Tray (35) in the following order: the 10-pound Removable Resistance Bar (67), the 20-pound Removable Resistance Bar (36), an 80-pound Resistance Bar (95), the 10-pound Center Resistance Bar (44), an 80-pound Resistance Bar (95), and the 40-pound Resistance Bar (96). Make sure the indicated rings are on the side shown and the arrows point toward the Tray.

Attach the Cover Plate (72), with the edges up, to the Tray (35) with two M8 x 19mm Button Head Screws (86).

9

 

 

 

 

 

65

70

 

 

 

 

 

75

 

 

 

59

 

 

 

 

 

93

 

 

 

 

 

 

 

 

38

 

10

 

 

 

 

 

65

 

 

34

 

 

 

 

 

 

 

 

 

 

 

 

59

 

 

 

 

 

38

 

 

Side View

 

34

4

 

10

 

 

 

 

 

 

 

 

 

 

4

 

 

 

 

34

 

 

 

 

 

10

 

 

 

 

 

 

 

 

96

 

 

 

95

 

 

79

 

 

 

 

 

 

 

36

 

85

 

 

67

 

 

 

 

 

44

85

85

 

100

 

 

 

 

 

88

 

 

 

 

85

 

 

 

 

 

 

 

 

 

101

 

 

 

85

 

20

 

 

 

11

 

86

 

 

 

 

 

 

 

 

 

 

72

Edges

 

 

 

 

up

 

 

 

 

 

 

 

 

 

 

 

96

 

Rings on

 

 

 

 

 

this side

 

 

 

 

 

 

 

 

44

 

 

35

 

 

 

95

 

 

 

 

95

 

18

 

 

 

4

 

67

 

36

 

Rods

 

 

 

 

 

18

 

 

 

 

 

8

Image 8
Contents QUESTIONS? Model No. WESY5983.3 Serial NoCall TOLL-FREE Mon.-Fri., 6 a.m.-6 p.m. MSTTable of Contents Important Precautions Assembled Dimensions Before YOU BeginAssembly Make Things Easier for YourselfPage Page Page Onto the tubes. Repeat with the tube on Leg Developer Do not overtighten the Locknut the Leg LeverMust be able to pivot easily Flat edge of the Pulley Guard is on the side Shown Locate the Long Cable 80. Insert one endSwivel Arm. Make sure the Cable is on the indi Arm 22. Make sure the Cable is on the indicat Ed side of the welded rod in the Swivel ArmPage Attaching the High Pulleys and LEG Lever AdjustmentsAdjusting the Seat Attaching the Accessories Adjusting the ResistanceAdjusting the Backrest Storing the Resistance SystemCable Diagram Using the Removable Resistance BarsAdjusting the LEG Developer Make sure the rings are pushed against the TrayExercise Guidelines Staying Motivated Muscle ChartCooling Down Date Exercise Resistance Sets RepsAerobic Exercise Thursday Aerobic Exercise DatePart Identification Chart Page Part LIST-Model No. WESY5983.3 Qty DescriptionExploded DRAWING-Model No. WESY5983.3 Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT Ordering Replacement PartsLimited Warranty