![](/images/new-backgrounds/1222775/22277519x1.webp)
15. Locate the Long Cable (80). Insert one end of | 15 |
|
|
|
|
the Cable through the welded tube on the indicat- |
|
|
|
| |
|
|
|
|
| |
ed end of the Cross Tube (11) and then through a |
|
|
| 80 |
|
Swivel Arm (22). If necessary, use the tip of a |
|
|
| 71 | |
screwdriver to pull the end of the Cable out of the |
|
|
| 10 | |
|
|
|
| ||
Swivel Arm. Be sure the Cable is on the indicat- |
|
|
|
| |
|
| 11 |
| ||
ed side of the welded rod in the Swivel Arm. |
|
|
|
|
|
Insert the Swivel Arm (22) into the welded tube |
|
| 28 |
| 22 |
|
|
|
| ||
on the Cross Tube (11). Secure the Swivel Arm |
|
|
|
| |
|
|
|
|
| |
with an M4 x 5mm Screw (10). |
|
|
|
| Rod |
Wrap the Long Cable (80) around a 90mm Pulley |
|
|
|
| 76 |
|
|
|
|
| |
(28). Attach the Pulley inside of the Swivel Arm |
|
|
|
|
|
(22) with an M10 x 42mm Button Head Bolt (71) |
|
|
|
|
|
and an M10 Nylon Locknut (76). |
|
|
|
|
|
16. Wrap the Long Cable (80) around a 90mm Pulley | 16 |
|
|
|
|
(28). Attach the Pulley and a Pulley Guard (29) to |
| Flat |
|
| |
|
|
|
| ||
the indicated M10 x 140mm Carriage Bolt (73) |
|
| Edge | 29 | 76 |
with an M10 Nylon Locknut (76). Make sure that |
|
|
|
|
|
the flat edge of the Pulley Guard is on the side |
|
|
|
|
|
shown. |
|
|
|
| 80 |
|
|
|
|
| 28 |
|
|
| 73 |
|
|
17. Attach a Pulley Housing (56) to the indicated “U”- | 17 |
|
|
|
|
channel on the |
|
|
|
| |
|
|
|
|
| |
(44) with an M10 x 102mm Button Head Bolt (24), |
|
|
|
|
|
two Pivot Bushings (74), and an M10 Nylon |
|
|
|
|
|
Locknut (76). |
|
|
|
|
|
Wrap the Long Cable (80) around a 90mm Pulley |
| 44 |
|
|
|
| 76 |
|
|
| |
(28). Attach the Pulley inside of the Pulley |
|
|
|
| |
|
|
| |||
Housing (56) with an M10 x 42mm Button Head | 74 |
| |||
|
|
| |||
Bolt (71) and an M10 Nylon Locknut (76). |
| 76 |
| ||
71 |
|
|
| ||
|
|
|
| ||
|
| 56 |
|
| |
|
|
|
|
| |
| 28 |
| 74 |
|
|
|
|
|
|
| |
|
| 80 | 24 |
|
|
|
|
|
|
| |
18. Wrap the Long Cable (80) under a 90mm Pulley | 18 |
|
|
|
|
(28) as shown. Attach the Pulley and a Pulley |
|
|
|
| |
|
|
|
|
| |
Guard (29) to the Upright (3) with an M10 x |
|
|
|
|
|
113mm Button Head Bolt (40) and an M10 Nylon | 3 |
|
|
|
|
Locknut (76). Make sure the flat edge of the |
| 28 |
|
| |
|
|
|
| ||
Pulley Guard is on the bottom. |
|
|
|
| |
|
|
|
|
| |
|
|
| 76 |
|
|
|
|
| 29 | 80 | |
| 40 |
|
| ||
|
|
|
|
| |
|
|
| Flat |
|
|
|
| Edge |
|
| |
| 10 |
|
|
|
|