Defy Appliances WMY 71283 MLCM manual Installation, Appropriate installation location

Page 7

4.1Installation

•Apply to the nearest authorized service agent for the installation of your product.

•Preparation of the location and electrical, tap water and waste water installations at the place of installation is under customer's responsibility.

•Make sure that the water inlet and discharge hoses as well as the power cable are not folded, pinched or crushed while pushing the product into its place after installation or cleaning procedures.

•Make sure that the installation and electrical connections of the product are performed by authorized service. Manufacturer shall not be held liable for damages that may arise from procedures carried out by unauthorized persons.

•Prior to installation, visually check if the product has any defects on it. If so, do not have it installed.

Damaged products cause risks for your safety.

4.1.1Appropriate installation location

•Place the product on a hard and level floor. Do not put it onto a carpet with high pile or other similar surfaces.

•When the washing machine and drier are placed on top of each other, their total weight –when loaded– amounts to 180 kilograms. Place the product on a solid and flat floor that has sufficient load carrying capacity!

•Do not place the product on the power cable.

•Do not install the product in the environments where the temperature falls below 0 ºC.

•Leave a minimum space of 1 cm between the machine and the furniture.

•On a graduated floor, do not place the product next to the edge or on a platform.

4.1.2Removing packaging reinforcement

Tilt the machine backwards to remove the packaging reinforcement. Remove the packaging reinforcement by pulling the ribbon. Do not make this operation alone by yourself.

4.1.3 Removing the transportation locks

1Loose all bolts with an appropriate wrench until they turn freely (C).

2Remove the transport safety bolts by turning them slightly.

3Insert the plastic covers in the bag containing the user manual to the openings on the rear panel. (P)

A CAUTION: Remove the transportation safety bolts before operating the washing machine! Otherwise, the product will be damaged.

C Keep the transportation safety bolts in a safe place to reuse when the washing machine needs to be moved again in the future.

Install the transport safety bolts in reverse order of the disassembly procedure.

Never move the product without the transportation safety bolts properly fixed in place!

Washing Machine / User’s Manual

7 / EN

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Document Number Please Register Your Machine AT Dear Customer Explanation of symbolsImportant instructions for safety and environment Disposing of the waste machine Package information Compliance with Weee DirectiveRated capacity kg Complying Commission Delegated Regulation EU No 1061/2010Removing packaging reinforcement InstallationAppropriate installation location Damaged products cause risks for your safetyConnecting the drain hose to the drain Connecting water supplyFor cold water inlet Do not make connections via extension cables or multi-plugs Adjusting the feetElectrical connection Initial usePreparation 11 / EN Using detergent and softenerDo not use bleaching agent and detergent by mixing them Using bleaches12 / EN Tips for efficient washing Spin speed selection LEDs Start / Pause button Operating the productControl panel Programme selection knobProgrammes Programme selectionCottons Use to drain the water in the machine Temperature selectionUse when you want to rinse or starch separately Spin speed selectionProgramme and consumption table End Time Auxiliary function selection18 / EN Loading door lock Switching the machine to pause modeChanging the auxiliary function, speed and temperature Starting the programmeChild Lock Canceling the programmeYour machine features Standby Mode Adding or taking out laundryCleaning the body and control panel Maintenance and cleaningCleaning the detergent drawer Cleaning the loading door and the drumReplace the filter Draining remaining water and cleaning the pump filterOrder to clean the dirty filter and discharge the water Turn and remove the pump filterProblem Reason Solution 24 / EN According to the water hardness Clean the dispenser with hot waterŠŠCall the Authorized Service Agent WashingOwner’s responsibility Av da Industrias, Parcela No.735 * 735A Machava, Maputo Service CentresPatterson Road, North End, Port Elizabeth 6001 Botswana Tel +267 390 3996 I 390 Fax +267 31828 / EN Warranty
Top Page Image Contents