Electrolux 1620 manual Connecting the appliance to the water supply, Permanent Connection

Page 41

Permanent Connection

In the case of a permanent connection it is necessary that you install a double pole switch between the appliance and the electricity supply (mains), with a minimum gap of 3mm between the switch contacts and of a type suitable for the required load in compliance with the current electrical regulations.

The switch must not break the yellow and green earth cable at any point.

This appliance complies with the requirements laid out in the EEC Di- rective 76/899.

Voltage 240 V AC: Fuse rating 13amps See rating plate for further information. This appliance meets VDE requirements.

Particular regulations of local electricity authorities must be observed. This appliance conforms to EEC Directive No. 82/499/EWG on radio in- terference.

1 WARNING! Repairs to electrical appliances must only be carried out by trained personnel. Improper repairs may lead to serious risks for the us- er.

Connecting the appliance to the water supply

Important:

This appliance must not be connected to the hot water supply.

When connecting the appliance, use only new hose kits.

Only connect the appliance to the drinking water supply. Rain water or water for industrial use may only be used if it fulfils the require- ments of DIN1986 and DIN1988.

Do not kink or crush the water inlet hose or drain hose.

Permitted water pressure

The water pressure must be at least 1 bar (=10N/cm2 =0.1MPa), and may be a maximum of 10bar (=100N/cm2 =1MPa).

If more than 10bar: Connect a pressure reduction valve.

If less than 1bar: Disconnect the appliance end of the inlet hose from the solenoid inlet valve and remove the flow meter. (In addition re- move the filter using pointed pliers and take out the rubber gasket behind it.) Replace the filter.

41

Image 41
Contents Lavamat Lavalogic Dear Customer Following symbols are used in the textContents Child safety device Safety information concerning installationPrior to using the appliance for the first time SafetyChild safety Follow the Installation and connection instructionsResulting overheating may constitute a fire hazard General safetyPress the control knob to switch off the appliance Control panel with display Indicators in the displayDescription of the appliance Keys Main control featuresControl knob Programme Programme overviewIKN Short Spin Icates, woollens, silk Before the first wash Setting the timePreparing and sorting washing Carrying out a wash programme prior to first useSetting a programme Switching on the applianceChanging the temperature Running a wash cycleSelecting options Press the Options key Press the Select key. The symbol appears in the displayPress the Select key Symbol appears in the display Current LOAD/DETERGENT display Opening the door/Loading the washingWashing powder/tablets for the main wash cycle If you are using liquid detergentAdding detergent/conditioner Programme progress Starting a programmeInterrupting a programme/Adding washing Interrupting a programmeIf Rinse Hold has been selected Washing cycle complete/Removing the washingSetting extra options Then press the Back key 3 times Saving a programme settingPress the Save key Press the Clear key Clearing a stored programme settingLanguage Programme protection Setting programme protectionStart the programme Removing programme protectionDeactivating the child safety device Child safety deviceDetergent drawer Cleaning and careWashing drum Door and rubber collarRemedying small malfunctions yourself What to do ifOnly a few large items There are grey stains on the washing If the wash result is not satisfactoryFoam can still be seen following the final rinse There are white residues on the washingCarrying out an emergency drain When the water has all drained awayDrain pump Old appliance DisposalPackaging material Consumption values Technical dataThis washing machine cannot be built-in Safety information concerning installationWhen using a sack trolley to transport the washing machine Installing the applianceTransporting the appliance Removing the transit packagingWhere to install If the appliance is to stand on a base Making the appliance levelElectrical Connection Brown Live Wire coloured green and yellowPermitted water pressure Connecting the appliance to the water supplyPermanent Connection 35m long pressure hose is supplied with the appliance Water inletFor drainage into an outlet From your Service Force CentreWater Drainage Pumping heights of over 1 metre Great Britain Warranty conditionsAutres agences étrangères assurant le service après-vente Further after-sales service agencies overseasWeitere Kundendienststellen im Ausland Otros puntos de Postventa en el extranjeroCustomer Service Centres Hungary Page Page Customer Care 0870 5 929For general enquiries concerning Major AppliancesAEG Hausgeräte GmbH Postfach 90327 Nürnberg Copyright by AEG