Electrolux 10500 VI manual Positioning, Levelling, Set the machine

Page 44

Installation

Set the machine

upright and remove the two remaining bolts from the back.

Pull out the three plastic spacers from

the holes into which the bolts were fit- ted.

Plug the open holes with the plugs which you will find in the envelope con- taining the instruction booklet.

You are advised to keep all transit devices so that they can be refitted if the machine ever has to be transported again.

Positioning

Install the machine on a flat hard floor.

Make sure that air circulation around the machine is not impeded by carpets, rugs etc.

•Before placing it on small tiles, apply a rubber coating.

•Never try to correct any unevenness in the floor by putting pieces of wood, cardboard or similar materials under the machine.

•If it is impossible to avoid positioning the machine next to a gas cooker or coal-burning stove, an insulating panel (85x57 cm) covered with aluminium foil on the side facing the cooker or stove, must be inserted between the two appliances;

•The machine must not be installed in rooms where the temperature can drop below 0°C.

•The water inlet hose and the drain hose must not be kinked.

•Please ensure that when the appliance is installed, it is easily accessi- ble for the engineer in the event of a breakdown.

Levelling

Carefully level by screwing the adjustable feet in or out. Never place cardboard, wood or similar materials under the machine to compensate for any unevenness in the floor.

44

Image 44

Contents Lavamat 10500 Dear customer Contents Programme charts wash and special programmes Contents Installation Safety instructionsGeneral safety Child safety During useDisposal Tips for environmental protectionPackaging materials MachineMain features of your washing machine Description of the appliance Front viewAccording to the type of laundry Control panelProgramme selector dial Delay Start button ON/OFF buttonMains-on light START/PAUSE buttonProgramme Option buttons This function cannot be used with Quick Wash and PrewashQuick Wash Display shows the following information DisplayProgramme progress display Cancelling/Altering a programme Opening the door after the programme has startedBefore the first wash Programme chartDetergent dispenser drawer Preparing the wash cycle Sorting out and preparing the laundrySynthetics Easy-cares Types of fabric and care labelsCotton Delicates 40 Detergents and additives Which detergent?Which form? Traditional PowdersHow to wash Switching the machine onLoad the laundry Add detergent and additiveSelection of the Delay Start option Selection of the desired wash programmeAt the end of the programme If the delay start option has been selected,Starting the programme Programme chart Wash programmesSpecial programmes WoolCleaning and maintenance Maintenance WashPeriodical cleaning Exterior After each washDoor seal Drain filterWater inlet filter Pull out the filterFrost precautions Emergency emptying outTroubleshooting Something not working?Problem Noisy Feet have not been Problem Possible cause Unsatisfactory washing results If grey stains remain on the laundryFoam is still visible even after the last rinse White residue is left on the laundryThis appliance complies with the following EC directives Technical dataWater pressure 50-800 kPa Service & Spare Parts Service & Spare Parts08705 929 Help us to help youCustomer care Guarantee Conditions European Guarantee Italy Pordenone +39 1678 Sweden Stockholm +46 738 Slough +44Instructions for installation and electrical connection Safety instructions for the installerRear view Dimensions of the applianceFront view and side view Installation UnpackingCarefully slide out the right poly- thene bag Previously removed screwSet the machine PositioningLevelling Do not connect to a hot water supply Water inlet cold water connection onlyWater drainage Interest of the environment Upright standpipe should have a miniElbow to the top of the pipe see dia Covered with waterElectrical connections Accordance with the following codeGreen and Yellow Earth Blue Brown LivePermanent connection Preparation and assembly of the door Building-inDoor HingesMounting the door Counter-magnetInstalled adjust all four Due to the additional 40 mm height required, ensureDrill four fixing holes see Position the base into See Fig. H With the appliance