Electrolux 10500 VI manual Water inlet cold water connection only, Water drainage

Page 45

Installation

Water inlet (cold water connection only)

Connect the hose

to a tap with a 3/4” thread.

Installation

should comply with local water authority and

building regula- tions’ require- ments.

Set the hose correctly by loosening the ring nut. After positioning the inlet hose, be sure to tighten the ring nut again to prevent leaks.

Do not connect to a hot water supply.

The inlet hose is provided with a water stop device, which protects against damage caused by water leaks in the hose which could develop due to natural ageing of the hose. This fault is shown by a red sector in

the window “A”. Should this occur, turn the A water tap off and refer to your Service Force Centre to replace the hose.

Water drainage

The appliance drain hose should hook into a standpipe, the hook in the drain hose is formed using the plastic “U-Piece” supplied. The standpipe should have an internal diameter of approximately 38 mm (see dia- gram) thus ensuring there is an air break between the drain hose and standpipe.

When discharging into a stand- pipe ensure that the top of the curve in the hose end is no more than 90 cm (35.4”) and no less than 60 cm (23.6”) above floor level.

3 pin

Max. 90 cm.(35.4")

Min.60 cm.(23.6")

45

Image 45

Contents Lavamat 10500 Dear customer Contents Programme charts wash and special programmes Contents Safety instructions General safetyInstallation During use Child safetyTips for environmental protection DisposalPackaging materials MachineMain features of your washing machine Front view Description of the applianceControl panel Programme selector dialAccording to the type of laundry ON/OFF button Delay Start buttonMains-on light START/PAUSE buttonThis function cannot be used with Quick Wash and Prewash Programme Option buttonsQuick Wash Display Programme progress displayDisplay shows the following information Opening the door after the programme has started Cancelling/Altering a programmeProgramme chart Detergent dispenser drawerBefore the first wash Sorting out and preparing the laundry Preparing the wash cycleTypes of fabric and care labels CottonSynthetics Easy-cares Delicates 40 Which detergent? Detergents and additivesTraditional Powders Which form?Switching the machine on How to washLoad the laundry Add detergent and additiveSelection of the desired wash programme Selection of the Delay Start optionIf the delay start option has been selected, Starting the programmeAt the end of the programme Wash programmes Programme chartWool Special programmesMaintenance Wash Cleaning and maintenancePeriodical cleaning Exterior After each washDrain filter Door sealWater inlet filter Pull out the filterEmergency emptying out Frost precautionsSomething not working? TroubleshootingProblem Noisy Feet have not been Problem Possible cause If grey stains remain on the laundry Unsatisfactory washing resultsFoam is still visible even after the last rinse White residue is left on the laundryTechnical data Water pressure 50-800 kPaThis appliance complies with the following EC directives Service & Spare Parts Service & Spare Parts08705 929 Help us to help youCustomer care Guarantee Conditions Italy Pordenone +39 1678 Sweden Stockholm +46 738 Slough +44 European GuaranteeSafety instructions for the installer Instructions for installation and electrical connectionDimensions of the appliance Front view and side viewRear view Unpacking InstallationCarefully slide out the right poly- thene bag Previously removed screwPositioning LevellingSet the machine Water inlet cold water connection only Water drainageDo not connect to a hot water supply Upright standpipe should have a mini Interest of the environmentElbow to the top of the pipe see dia Covered with waterAccordance with the following code Electrical connectionsGreen and Yellow Earth Blue Brown LivePermanent connection Building-in Preparation and assembly of the doorDoor HingesCounter-magnet Mounting the doorDue to the additional 40 mm height required, ensure Installed adjust all fourDrill four fixing holes see Position the base into See Fig. H With the appliance